NEC express5800 A2010b

To Next Page

To Previous Page

7. Using Remote Management

Chapter 3 Setup

• Select Enable or disable IPv6.

• Select Static or Dynamic for IPv6 Address Assign Mode.

• Specify static address (IPv6 current static address, IPv6 prefix length, and IPv6 gateway address)

Express5800/A1040b, A2040b, A2020b, A2010b User's Guide

324

Main Page

Default Chapter2
- Documents Provided with this Product2
- Table of Contents3
- Contents3
- Notations Used in this Document9
- Trademarks11
- License Notification17
- Regulatory Notices20
- Warnings and Additions to this Document23
Chapter 1 General Description106
Introduction107
Accessories108
Standard Features109
- Feature of each Model112
Introducing the Server116
- Important Points for System Configuration116
  - Operation Procedures116
  - Operation Status/Failure Monitoring and Maintenance117
- Notes on Configuring and Operating the System118
- Management Features121
- Firmware and Software Version Management126
Names and Functions of Components127
- Front View (with Front Bezel Mounted)127
- Front View (with Front Bezel Removed)128
- Rear View130
- External View131
- Internal View132
- LED Indications133
Chapter 2 Preparations143
Installing / Removing Internal Options144
- Safety Precautions145
- Anti-Static Measures151
- Parts Able to be Added/Replaced by Customers157
- Overview of Installation and Removal159
- Confirming Servers (UID Switch)163
- Removing Front Bezel164
- Optical Disk Drive165
  - Installation165
  - Removal166
- Hard Disk Drive168
- Power Supply Unit175
  - Installation176
  - Removal177
- Cooling Fan180
  - Replacement180
- Internal Flash Memory187
  - Installation187
- Processor (CPU)188
  - Installation188
  - Setting Required after Installation188
- Memory Riser (MR)189
  - Installation189
- DIMM190
- Extra Battery for RAID Controller202
  - Handling Precautions202
  - Installation202
- PCI Card203
- Installing the Front Bezel205
- SUV Cable206
  - Installation206
  - Removal208
Installation and Connection209
- Installation209
  - Installing Rack209
  - Installing the Server to the Rack or Removing It from the Rack216
- Connection237
  - Connecting Power Cable245
  - Connecting to Uninterruptible Power Supply (UPS)247
Chapter 3 Setup248
Before Starting Setup249
- Service Pack Support249
- Option Boards Supported by EXPRESSBUILDER249
Setup250
- Setup of Management PC250
- Setup of Hardware250
- Setup of Operating System252
- Setup for Solving Problems253
- Advanced Setup254
  - Reinstallation When Multiple Logical Drives Exist254
Turning on the Server255
- Post256
  - POST Flow256
  - POST Error Messages257
BIOS Setup Utility (SETUP)258
- Overview258
- Starting and Exiting SETUP Utility258
  - Starting SETUP258
  - Exiting SETUP258
- Description on On-Screen Items and Key Usage259
- Cases that Require Configuration261
- EFI Shell263
  - EFI Shell Command264
EXPRESSSCOPE Engine SP3266
- Overview266
- Default Network Settings266
  - A1040B266
  - A2040B/A2020B/A2010B267
- Http/Https267
- Login Using Ldap/Active Directory267
- EXPRESSSCOPE Engine SP3 Network Configuration268
Expressbuilder286
- Features of EXPRESSBUILDER286
- Starting EXPRESSBUILDER286
Using Remote Management287
- Login and Logout287
  - Login287
  - Logout289
- Header Menu290
- Server Panel291
- System293
- Remote Access308
- Remote KVM313
- Configuration316
- Update379
  - BMC Firmware379
  - System BIOS381
- Maintenance384
- Capacity396
- Standby Web Console400
  - Failover400
- MC Web Console Access Level401
- BMC Web Console Language/Help403
Smash-Clp408
- Overview408
- Connecting to BMC408
- Login and Logout409
  - Login409
  - Logout409
- Basic Commands410
- Remote Control414
- Remote Console415
- UID Switch Control417
- System Event Log418
  - Viewing System Event Log418
  - Change Setting of System Event Log419
- Access Log420
- User Settings424
- Network Settings425
- Power Consumption Control429
- Confirming System Information430
- Special Extended Command433
- Viewing and Modifying Server Configuration Information438
- Command Line Interface of Standby BMC442
WS-Management447
- Overview447
- Power Control448
- Sensor Information455
  - Enumuration455
  - Displaying Specified Sensor456
Installing Software Components457
Turning off the Server458
Chapter 4 Appendix459
- EXPRESS5800/ A1040B (1/2)460
Specifications460
- EXPRESS5800/ A1040B (2/2)462
- EXPRESS5800/ A2040B (1/2)464
- EXPRESS5800/ A2040B (2/2)466
- EXPRESS5800/ A2020B (1/2)468
- EXPRESS5800/ A2020B (2/2)468
  - EXPRESS5800/ A2020B (2/2)470
- EXPRESS5800/ A2010B (1/2)472
- EXPRESS5800/ A2010B (2/2)472
  - EXPRESS5800/ A2010B (2/2)474
Operation Mode476
Settings for each os490

NEC express5800 A2010b - Page 324

Table of Contents

Related product manuals