Omron CP1L - Page 677

643
Auxiliary Area Allocations by Address Appendix D
A393 A393.00
to
A393.07
Serial Port 2
PT Communi-
cations Flags
(CP1L M-type
CPU Units)
The corresponding bit will be ON
when the serial port 2 of a CP1L M-
type CPU Unit is communicating with
a PT in NT Link or Serial PLC Link
mode.
Bits 0 to 7 correspond to units 0 to 7.
ON: Commu-
nicating
OFF: Not
communicat-
ing
Retained Cleared Refreshed
when there
is a nor-
mal
response
to the
token.
---
Serial Port 1
PT Communi-
cations Flags
(CP1L L-type
CPU Units)
The corresponding bit will be ON
when the serial port 1 of a CP1L L-
type CPU Unit is communicating with
a PT in NT Link or Serial PLC Link
mode.
Bits 0 to 7 correspond to units 0 to 7.
A393.08
to
A393.15
Serial Port 2
PT Priority
Registered
Flags (CP1L
M-type CPU
Units)
The corresponding bit will be ON for
the PT that has priority when the
serial port 2 of a CP1L M-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
These flags are written when the pri-
ority registration command is
received.
ON: Priority
registered
OFF: Priority
not registered
Retained Cleared See
Func-
tion
col-
umn.
---
Serial Port 1
PT Priority
Registered
Flags (CP1L
L-type CPU
Units)
The corresponding bit will be ON for
the PT that has priority when the
serial port 1 of a CP1L L-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
These flags are written when the pri-
ority registration command is
received.
A393.00
to
A393.15
Serial Port 2
Reception
Counter (No-
protocol
Mode) (CP1L
M-type CPU
Units)
Indicates (in binary) the number of
bytes of data received when the
serial port 2 of a CP1L M-type CPU
Unit is in no-protocol mode.
--- Retained Cleared Refreshed
when data
is received.
---
Serial Port 1
Reception
Counter (No-
protocol
Mode) (CP1L
L-type CPU
Units)
Indicates (in binary) the number of
bytes of data received when the
serial port 1 of a CP1L L-type CPU
Unit is in no-protocol mode.
A394 A394.00
to
A394.07
Serial Port 1
PT Communi-
cations Flags
(CP1L M-type
CPU Units)
The corresponding bit will be ON
when the serial port 1 of a CP1L M-
type CPU Unit is communicating with
a PT in NT link mode.
Bits 0 to 7 correspond to units 0 to 7.
ON: Commu-
nicating
OFF: Not
communicat-
ing
Retained Cleared Refreshed
when there
is a nor-
mal
response
to the
token.
---
A394.08
to
A394.15
Serial Port 1
PT Priority
Registered
Flags (CP1L
M-type CPU
Units)
The corresponding bit will be ON for
the PT that has priority when the
serial port 1 of a CP1L M-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
ON: Priority
registered
OFF: Priority
not registered
Retained Cleared See
Func-
tion col-
umn.
---
A394.00
to
A394.15
Serial Port 1
Reception
Counter (No-
protocol
Mode) (CP1L
L-type CPU
Units)
Indicates (in binary) the number of
bytes of data received when serial
port 1 of a CP1L L-type CPU Unit is
in no-protocol mode.
--- Retained Cleared Refreshed
when data
is received.
---
A395 A395.12 DIP Switch
Pin 6 Status
Flag
The status of pin 6 on the DIP switch
on the front of the CPU Unit is written
to this flag every cycle.
ON: Pin 6 ON
OFF: Pin 6
OFF
Retained See
Func-
tion col-
umn.
Written
every
cycle.
---
Address Name Function Settings Status
after
mode
change
Status
at star-
tup
Write
timing
Related
flags, set-
tings
Words Bits