Omron MX2 Series User Manual

1 Overview
1 - 30
Multi-function Compact Inverter 3G3MX2-EV2 User’s Manual (I666-E1)
Parameter
No.
Function name
Data range
3G3MX2-E
3G3MX2-EV2
C004
Multi-function Input 4 Selec- tion
00 to 09, 11 to 16, 18 to 24, 27
to 29, 31 to 42, 44, 46, 47, 50
to 53, 56 to 62, 65 to 70, 73,
78, 81 to 86, 91
255: no
00 to 09, 11 to 16, 18, 20 to 24,
27 to 29, 31 to 42, 44, 46, 47,
50 to 53, 56 to 62, 65 to 70,
73, 81 to 86, 91
255: no
C042
Arrival Frequency During Accel-
eration 1
0.00 to 400.00 (580.00)
*1
0.00 to 590.00
C043
Arrival Frequency During Decel-
eration 1
0.00 to 400.00 (580.00)
*1
0.00 to 590.00
C045
Arrival Frequency During Accel-
eration 2
0.00 to 400.00 (580.00)
*1
0.00 to 590.00
C046
Arrival Frequency During Decel-
eration 2
0.00 to 400.00 (580.00)
*1
0.00 to 590.00
P071
Origin Search Mode 2 Fre-
quency
0.00 to 400.00 (580.00)
*1
0.00 to 590.00
*1. In high-frequency mode.
From Soft Lock Selection (b031) of the 3G3MX2-E Series Inverter, 10 (Data can be changed during
RUN) selection is deleted, and Data can be changed during RUN is always enabled.
To prevent unintended changes to parameters, use the Soft Lock Selection (b031). (Refer to 7-6-1 Soft
Lock Function (SFT) on page 7-54). To prevent unintended changes, use the password function (refer
to 7-6-9 Password Function on page 7-57).
However, it is not possible to write-protect only a portion of the parameters.
The 3G3MX2-EV2 Series Inverter allows you to change the following parameters during RUN, although
the 3G3MX2-E Series Inverter does not allow it. For parameters for which you can change data during
RUN, refer to the lists in Section 4 Parameter List.
Parameter No.
Function name
F004
RUN Direction Selection
A081/A282
AVR Selection
A095/A295
2-step Acceleration Frequency
A096/A296
2-step Deceleration Frequency
b051
Starting Voltage on Power Interruption
b052
Deceleration Hold Level on Power Interruption
b053
Deceleration Time on Power Interruption
b054
Deceleration Starting Width on Power Interruption
b093
Total Fan Operation Time Clear
C096
Communication Selection
H117
PM Motor Starting Current
H118
PM Motor Starting Time
P039
Speed Limit Value in Torque Control (Forward)
P040
Speed Limit Value in Torque Control (Reverse)
P081
Position Store Selection at Power Off
P082
Position Data at Power Off
P083
Preset Position Data
P200
Modbus Mapping Function Selection
P201 to P210
Modbus Mapping
External Register 1 to 10
Data can be changed during RUN

Omron MX2 Series Specifications

General

Cooling Method	Fan cooling
Output Frequency Range	0.1 to 400 Hz
Control Method	V/f control, Sensorless vector control
Protection Functions	Overcurrent, overvoltage, undervoltage, overload, overheating, short circuit
Communication Options	Modbus RTU
Overload Capacity	150% for 60 seconds
Braking Unit	Built-in
Ambient Operating Temperature	-10°C to +50°C
Enclosure	IP20
Storage Temperature	-20°C to +65°C
Humidity	5 to 95% RH (non-condensing)
Altitude	Up to 1000m
Power Supply Voltage	200-240V AC
Input Voltage	3-phase 200-240V AC