R&S NRP2 - Page 236

Remote Control - Commands
R&S
®
NRP2
218User Manual 1173.9157.02 ─ 03
FETCh<[1]..8>:ARRay[:POWer][:AVG]
FETCh<[1]..8>:ARRay[:POWer][:AVG]:RELative
FETCh<[1]..8>:ARRay[:POWer][:AVG]:DIFFerence
FETCh<[1]..8>:ARRay[:POWer][:AVG]:DIFFerence:RELative
FETCh<[1]..8>:ARRay[:POWer][:AVG]:SUM
FETCh<[1]..8>:ARRay[:POWer][:AVG]:SUM:RELative
FETCh<[1]..8>:ARRay[:POWer][:AVG]:RATio
FETCh<[1]..8>:ARRay[:POWer][:AVG]:RATio:RELative
FETCh<[1]..8>:ARRay[:POWer][:AVG]:SWR
FETCh<[1]..8>:ARRay[:POWer][:AVG]:REFLection
FETCh<[1]..8>:ARRay[:POWer][:AVG]:RLOSs (<buffered_size>),
[<expected_value>[,<resolution>]] [,<source_list>]
FETCh commands for measurement mode ContAv with buffering.
FETCh<[1]..8>:XTIMe[:POWer]
FETCh<[1]..8>:XTIMe[:POWer]:RATio (<scope_size>), <capture_time>
[,<source_list>]
FETCh commands for measurement mode Trace.
FETCh<[1]..8>:STATistics:CCDF
FETCh<[1]..8>:STATistics:PDF (<statistics_size>), <capture_time> [,<source_list>]
FETCh commands for measurement mode Statistics.
6.4.8 READ commands
This chapter lists all READ commands. For a description of the command syntax, the
calculation functions and the parameter list see chapter 6.4.3, "Syntactical Structure of
High-Level Measurement Commands ", on page 209, chapter 6.4.5, "Calculation func-
tions - High level commands", on page 213, and chapter 6.4.4, "Parameter list descrip-
tion", on page 210.
READ<[1]..8>[:SCALar][:POWer][:AVG]
READ<[1]..8>[:SCALar][:POWer][:AVG]:RELative
READ<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence
READ<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence:RELative
READ<[1]..8>[:SCALar][:POWer][:AVG]:SUM
READ<[1]..8>[:SCALar][:POWer][:AVG]:SUM:RELative
READ<[1]..8>[:SCALar][:POWer][:AVG]:RATio
READ<[1]..8>[:SCALar][:POWer][:AVG]:RATio:RELative
READ<[1]..8>[:SCALar][:POWer][:AVG]:SWR
READ<[1]..8>[:SCALar][:POWer][:AVG]:REFLection
READ<[1]..8>[:SCALar][:POWer][:AVG]:RLOSs [<expected_value>[,<resolution>]]
[,<source_list>]
READ commands for measurement mode ContAv.
High-Level Measurement Commands (CONFigure, MEASure, READ and FETCh)