R&S NRP2 - Measurement Commands

Remote Control - Commands
R&S
®
NRP2
220User Manual 1173.9157.02 ─ 03
READ<[1]..8>:XTIMe[:POWer]
READ<[1]..8>:XTIMe[:POWer]:RATio (<scope_size>), <capture_time>
[,<source_list>]
READ commands for measurement mode Trace.
READ<[1]..8>:STATistics:CCDF
READ<[1]..8>:STATistics:PDF (<statistics_size>), <capture_time> [,<source_list>]
READ commands for measurement mode Statistics.
6.4.9 MEASurement commands
This chapter lists all MEASurement commands. For a description of the command syntax,
the calculation functions and the parameter list see chapter 6.4.3, "Syntactical Structure
of High-Level Measurement Commands ", on page 209, chapter 6.4.5, "Calculation func-
tions - High level commands", on page 213, and chapter 6.4.4, "Parameter list descrip-
tion", on page 210.
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:RELative
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:DIFFerence:RELative
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:SUM
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:SUM:RELative
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:RATio
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:RATio:RELative
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:SWR
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:REFLection
MEASurement<[1]..8>[:SCALar][:POWer][:AVG]:RLOSs
[<expected_value>[,<resolution>]][,<source_list>]
MEASurement commands for measurement mode ContAv.
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:RELative
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:DIFFerence
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:DIFFerence:RELative
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:SUM
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:SUM:RELative
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:RATio
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:RATio:RELative
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:SWR
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:REFLection
MEASurement<[1]..8>[:SCALar][:POWer]:TSLot:RLOSs <tslot_width>, <no_slots>,
<start_exclude>, <end_exclude>, [<expected_value> [,<resolution>]]
[,<source_list>]
MEASurement commands for measurement mode T'Slot.
High-Level Measurement Commands (CONFigure, MEASure, READ and FETCh)