Shimadzu GC-2014 Service Manual

Chapter 6 Maintenance Parts List
GC-2014 Service Manual
67

6.2 Maintenance Parts
GC-2014 Main Unit
P/N Description Previous P/N Compatibility Remarks
S221-73277-43 CPU UNIT, GC-2014 S221-47632-92

The board is in common with the
GC-2010.
S074-73306-08 LITHIUM BATTERY S074-73307-01

CR2032
S221-48460-42 POWER UNIT S221-48460-92

100-V system
S221-48460-49 POWER UNIT, CE S221-48460-39

200-V system (The plate was
changed in accordance with SSR
changes, so cannot be used with
older parts.)
S072-01665-36 FUSE, 15A

100-V system
S072-02004-23 FUSE, 218 5A

100-V system
S072-01665-34 FUSE, 10A

200-V system
S072-02004-21 FUSE, 218 3.15A

200-V system
S074-80427-61 POWER SUPPLY, LEA100F-24

200-V system
S074-80654-77 POWER SUPPLY, VS100B-24

100-V system
S221-47653-41 POWER SWITCH ASSY S221-47653-91

S221-74060-81 HEATER ASSY, COLUMN OVEN, 100 V S221-49613-91

S221-74060-82 HEATER ASSY, COLUMN OVEN, 115 V S221-49613-92

S221-74060-84 HEATER ASSY, COLUMN OVEN, 230 V S221-49613-34

S221-43695-41 PT SENSOR ASSY, COLUMN OVEN S221-43695-91

S221-43696-91
THERMOCOUPLE ASSY, COLUMN
OVEN

S221-43710 HOLDER, PT SENSOR

S221-73248-41 FAN MOTOR ASSY, 100 V S221-70072-91

In common with GC-2010
S221-73248-42 FAN MOTOR ASSY, 120 V S221-70072-92

In common with GC-2010
S221-73248-48 FAN MOTOR ASSY, 230 V S221-70072-34

In common with GC-2010
S221-73600 FAN S221-28247

Internal oven fan
S221-12949 COOLING FAN

Oven back fan
S221-47652 FLAP MOTOR

S221-73918-41 LCD ASSY, GC-2025 S221-48721-91

With gasket
S221-73821-42 PCB KEY ASSY, GC-2014 S221-70250-91

Change to new LCD scheduled
S221-46470-01 KEY RUBBER 1, KEY PANEL

S221-46471-01 KEY RUBBER 2, KEY PANEL

S221-75120-41 PCB DET I/ F, GC2014 S221-70254-91

S221-45745-41 PCB FLOW I/ F GC-2010 S221-45745-91

S221-73335-43 AFC-2014,SPL ASSY S221-47735-93

 For SPL
S221-75082-81 SPL-2014, STOCKED, 100-120 S221-70082-81

 SPL 100-V system (Gas leak
tests and ageing completed)
S221-75082-38 SPL-2014, STOCKED, 220 -240 S221-70082-38

 SPL 200-V system (Gas leak
tests and ageing completed)
S221-41286 SEPTUM NUT

S221-43597-01 COVER, RADIATING FIN

S221-44584 GUIDE, FOR NEEDLE FIN, AOC

S221-32705 CAP NUT, M5

0.5, SLOTTED

S221-16325-81 NUT, NOT SLOTTED

Pack of 10
S221-47251-41
(-43)
CHROMATOPAC SIGNAL CABLE, WIDE
(CE)
S221-47251-91
(-31)

For wide range output
(-43 is CE compliant)
S221-47251-42
(-44)
CHROMATOPAC SIGNAL CABLE,
LINEAR (CE)
S221-47251-92
(-32)

For linear output
(-44 is CE compliant)
S221-79044 INSTRUCTION MANUAL, GC-2014, J S221-40608

S221-79045 INSTRUCTION MANUAL, GC-2014, E S221-40609

S221-79042 OPERATION MANUAL, GC-2014, J S221-40606

S221-79043 OPERATION MANUAL,GC-2014, E S221-40607


Shimadzu GC-2014 Specifications

General

Type	Gas Chromatograph
Display	LCD
Maximum Heating Rate	120°C/min
Data Acquisition	Digital
Maximum Number of Detectors	4
Weight	Approx. 45 kg
Carrier Gas	Helium, Nitrogen, Hydrogen
Detector Options	FID, TCD, ECD, FPD
Injection Port	Split/Splitless, On-column
Gas Control	Electronic Flow Control (EFC)
Temperature Programming Rate	0.1 to 120 °C/min
Power Requirements	230 V AC, 50/60 Hz
Detector Temperature Range	Up to 400°C (depending on detector type)