Siemens Sinumerik 840D Series Function Manual

10.03
4.15 Parameters table
4-172
 Siemens AG, 2003. All rights reserved
SINUMERIK 840D/SIMODRIVE 611 digital, HLA Module (FBHLA) - 10.03 Edition
MD no. Name in NC
ware- Version
Max. Unit
Attribute
Firm-
Data type
Index Active
Version Min.Name in plaintext
5623 5625
UNS.WORD 4.13immediately-1000000PROG_SIGNAL_ON_DELAY 1.01Dropout delay for variable signaling function
5621
5620 5622 5624
UNS.WORD 4.13immediatelyHEX700PROG_SIGNAL_FLAGS 1.01Bits of variable signaling functions
UNS.WORD 4.13immediately-10000PROG_SIGNAL_NR 1.01Signal number of variable signaling functions UNS.WORD 4.13immediatelyHEXFFFFFF00PROG_SIGNAL_ADDRESS 1.01Address to be monitored by variable sign. funct.
UNS.WORD 4.13immediatelyHEXFFFFFF00PROG_SIGNAL_THRESHOLD 1.01Threshold for variable signaling functions
UNS.WORD 4.13immediatelyHEXFFFFFF00PROG_SIGNAL_HYSTERESIS 1.01Hysteresis for variable signaling functions
5626
UNS.WORD 4.13immediately-1000000PROG_SIGNAL_OFF_DELAY 1.01Dropout delay for variable signaling function
5650
UNS.WORDDiagnostic control 4.14immediatelyFFFF00DIAGNOSIS_CONTROL_FLAGS HEX 1.01
UNS.WORD
5600 5601 5605 5606 5609 5612 5613
UNS.WORD UNS.WORD FLOAT FLOAT FLOAT UNS.WORD UNS.WORD
5614
Config. shutdown response to RESET alarms Concealable alarms (Power On) Concealable alarms (Reset) Time for velocity controller at limit Threshold for velocity controller at limit Max. measuring speed of linear scale Config. shutdown response to PO alarms Valve spool monitoring timer
4.13 4.13 4.13 4.13 4.13 4.13 4.13 4.13
immediately immediately immediately immediately immediately immediately immediately immediately
HEX
HEX HEX
ms
mm/min mm/min
HEX
ms
FFFF FFFF FFFF
1000.0
120000.0 240000.0
FFFF
100
0 0 0
200.0
120000.0 240000.0
0
50
0
0 0
20.0
0.0 1.0
0 1
ALARM_REACTION_RESET ALARM_MASK_POWER_ON ALARM_MASK_RESET SPEEDCTRL_LIMIT_TIME SPEEDCTRL_LIMIT_THRESHOLD ENC_SPEED_LIMIT ALARM_REACTION_POWER_ON VALVE_ERROR_TIME
1.01 1.01 1.01 1.01 1.01 1.01 1.01 1.01
5551 5552 5553
WORD
FLOAT WORD
Offset adjustment for pressure sensor A Reference value of pressure sensor B at 10 V Offset adjustment for pressure sensor B
4.11 4.11 4.11
immediately immediately immediately
-
bar
-
32760 6000.0
32767
0
200.0
0
-32760
50.0
-32767
PRESSURE_SENS_A_OFFS PRESSURE_SENS_B_REF PRESSURE_SENS_B_OFFS
1.01 1.01 1.01
5648
UNS.WORD -immediately-799900VALVE_ID_PARAMS1 1.01.12Valve identification parameter 1
5649
UNS.WORD -immediately-799900VALVE_ID_PARAMS2 1.01.12Valve identification parameter 2
5610
UNS.WORD
Diagnostic functions
-Power OnHEX
300
DIAGNOSIS_ACTIVATION_FLAGS
1.01
5522 5530 5531 5532
FLOAT UNS.WORD UNS.WORD UNS.WORD
Time constant for velocity actual value filter Safety configuration Manipulated variable enable delay Power enable delay time
-
4.12 4.12 4.12
Power On immediately immediately immediately
-
HEX
ms ms
0
3F
500 300
0
4
300 100
0 0 0 0
ACT_SPEED_FILTER_TIME CYLINDER_SAFETY_CONFIG OUTPUT_ENABLE_DELAY POWER_ENABLE_DELAY
1.01.08
1.01 1.01 1.01
FLOAT
5550 Reference value of pressure sensor A at 10 V
4.11immediately
bar6000.0200.0 50.0PRESSURE_SENS_A_REF
1.01
5520
FLOAT
Band-stop filter natural frequency for vel. filter 1
4.3.1immediately0...7
%141.0100.0 1.0SPEED_FILTER_1_BS_FREQ
1.01
Sec- tion
4 Firmware Drive Functions

Siemens Sinumerik 840D Series Specifications

General

Axes	Up to 31 axes
Power Supply	24 V DC
Control Type	CNC
Interface	Ethernet, PROFIBUS
Display	TFT color display
PLC	Integrated PLC (programmable logic controller)
Operating Temperature	0°C to 45°C
Relative Humidity	Up to 95% (non-condensing)
Max. Number of Channels	Up to 10 channels