4 – Mixer configuration and settings
Synchronizing audio settings
If the Sonicview has control privileges after mounting, the
SB-16D sampling rate and reference level (both analog and
digital) settings will automatically be synchronized with those
of that Sonicview. Moreover, it will also be set as the device for
snapshot recall and set as the device with priority for Dante
output routing.
Dante routing
Routing of Dante I/O for mounted SB-16Ds and the Sonicview
can be done automatically.
On the other hand, routing can be left to Dante Controller and
the Sonicview can be set to not do routing.
Use the Routing control setting on the Controller Settings page
to set this. (See “2 Routing control setting” on page 59.)
o To conduct Dante routing from the Sonicview for SB-16D
units mounted on it, set the Routing control setting to “This
Console”.
Dante routing will be set automatically when mounted.
In this case, depending on the SB-16D mounting position,
the mounted SB-16D I/O port and this unit’s built-in Dante
I/O will be routed for Dante automatically when mounting
occurs as shown below.
When Sync Clock is 48 kHz
Mounting position in
Mounted Device area
Routing destination
Top
Built-in Dante I/O 1–16 of this
unit
2nd from top
Built-in Dante I/O 17–32 of this
unit
3rd from top
Built-in Dante I/O 33–48 of this
unit
4th from top
Built-in Dante I/O 49–64 of this
unit
When Sync Clock is 96 kHz
Mounting position in
Mounted Device area
Routing destination
Top
Built-in Dante I/O 1–16 of this
unit
2nd from top
Built-in Dante I/O 17–32 of this
unit
3rd from top
This will not be routed
automatically. Use Dante
Controller to route Dante I/O
1–16 for the IF-DA64 installed in
this unit and Dante I/O 1–16 for
the mounted SB-16D.
Mounting position in
Mounted Device area
Routing destination
4th from top
This will not be routed
automatically. Use Dante
Controller to route Dante I/O
17–32 for the IF-DA64 installed
in this unit and Dante I/O 1–16
for the mounted SB-16D.
NOTE
When the Routing control setting is changed from “Dante
Controller” to “This Console”, if executing automatic Dante
routing changes the Dante input routing of this unit, the
following message will appear, confirming whether to match
routing with the mounting status.
Devices other than this sonicview are routing to the
mounted SB-16D.
Do you want to KEEP the routing? Or Change the routing to
this Sonicview?
[KEEP] [CHANGE]
Tapping the KEEP button will switch routing control to “This
Console” but the Dante routing setting will be retained as
is. If an SB-16D is mounted after switching to “This Console”,
routing will occur automatically.
Tapping the CHANGE button will change the Dante routing
according to the mounting status. In this case, output routing
from the Sonicview to other Dante devices will be retained
as is, and output routing from the Sonicview to mounted SB-
16D unit will be added.
i Example of Dante routing when Routing control setting is
“Dante Controller”
Sonicview 16 /
Sonicview 24
Dante
device
Mounted
SB-16D
i Dante routing state when the Routing control setting is
switched to “This Console” from the above state and the
CHANGE button is tapped
Sonicview 16 /
Sonicview 24
Dante
device
Mounted
SB-16D
o To conduct Dante routing for the Sonicview from Dante
Controller, set the Routing control setting to “Dante
Controller”.
This will enable routing from Dante Controller.
i When set to conduct Dante routing from Dante Controller,
routing settings cannot be conducted from the Sonicview
even for SB-16D units.
NOTE
Routing for mounted SB-16Ds will be retained as is. If an
SB-16D is mounted after the routing control setting is set to
“Dante Controller”, routing will not occur automatically.
68 TASCAM Sonicview 16/Sonicview 24 V1.1.0
To Next Page
Loading...
Need help?
General
