Teledyne 200E - Page 12

Model 200E Instruction Manual M200E Documentation
LIST OF TABLES
Table 2-1: Model 200E Basic Unit Specifications............................................................... 5
Table 3-1: Inlet / Outlet Connector Nomenclature .......................................................... 13
Table 3-2: Analog Output Pin-Outs............................................................................... 18
Table 3-3: Status Output Signals ................................................................................. 18
Table 3-4: Control Input Signals.................................................................................. 19
Table 3-5: Front Panel Display During System Warm-Up ................................................. 21
Table 3-6: Possible Warning Messages at Start-Up ......................................................... 22
Table 5-1: IZS or Z/S Valve States .............................................................................. 35
Table 5-2: Available Permeation Source Options ............................................................ 36
Table 5-3: Contents of Zero Air Scrubber Maintenance Kit............................................... 37
Table 5-4: Dryer and NH
3
Removal Options................................................................... 39
Table 6-1: Analyzer Operating modes........................................................................... 41
Table 6-2: Test Functions Defined................................................................................ 43
Table 6-3: List of Warning Messages Revision C.4 .......................................................... 44
Table 6-4: Password Levels......................................................................................... 45
Table 6-5: Variable Names (VARS) Revision C.4............................................................. 55
Table 6-6: M200E Diagnostic (DIAG) Functions.............................................................. 57
Table 6-7: DIAG - Analog I/O Functions........................................................................ 60
Table 6-8: Analog Output Voltage Ranges ..................................................................... 60
Table 6-9: Analog Output Current Loop Range............................................................... 61
Table 6-10: Analog Output Pin Assignments.................................................................... 61
Table 6-11: Voltage Tolerances for Analog Output Calibration............................................ 64
Table 6-12: Current Loop Output Calibration with Resistor ................................................ 68
Table 6-13: Test Parameters Available for Analog Output A4 ............................................. 69
Table 6-14: Status Output Pin Assignments .................................................................... 73
Table 6-15: Control Input Pin Assignments ..................................................................... 74
Table 6-16: COM1 and COM2 DB-9 Pin Assignments ........................................................ 77
Table 6-17: COM Port Communication Modes .................................................................. 78
Table 6-18: Ethernet Status Indicators........................................................................... 81
Table 6-19: Front Panel LED Status Indicators for iDAS .................................................... 85
Table 6-20: iDAS Data Channel Properties ...................................................................... 87
Table 6-21: iDAS Data Parameter Functions.................................................................... 88
Table 6-22: M200E Default iDAS Configuration, Revision C.7. ............................................ 90
Table 6-23: Terminal Mode Software Commands ............................................................103
Table 6-24: Command Types .......................................................................................104
Table 6-25: Serial Interface Documents ........................................................................108
Table 7-1: IZS Option Valve States with CAL_ON_NO
2
Turned ON ...................................117
Table 7-2: AutoCal Modes..........................................................................................122
Table 7-3: AutoCal Attribute Setup Parameters.............................................................122
Table 7-4: Example Auto-Cal Sequence .......................................................................123
Table 7-5: Calibration Data Quality Evaluation..............................................................125
Table 8-1: Activity Matrix for EPA Calibration Equipment and Supplies .............................128
Table 8-2: Activity Matrix for Calibration Procedure .......................................................128
Table 8-3: Definition of Level 1 and Level 2 Zero and Span Checks..................................136
Table 8-4: Activity Matrix for Data Quality ...................................................................137
Table 9-1: M200E Preventive Maintenance Schedule......................................................141
Table 9-2: Predictive Uses for Test Functions................................................................143
Table 10-1: List of Interferents ....................................................................................160
Table 10-2: M200E Valve Cycle Phases..........................................................................163
Table 10-3: M200E Gas Flow Rates...............................................................................169
Table 10-4: Front Panel Status LED’s ............................................................................183
044100102 Rev A xi