Teledyne 200E - Page 5

M200E Documentation Model 200E Instruction Manual
5.10. Extended Warranty (Options 92 & 93)..........................................................................40
6. OPERATING INSTRUCTIONS ........................................................................................... 41
6.1. Overview of Operating Modes .......................................................................................41
6.2. Sample Mode .............................................................................................................42
6.2.1. Test Functions .....................................................................................................42
6.2.2. Warning Messages................................................................................................44
6.2.3. Calibration Functions ............................................................................................44
6.3. Calibration Mode.........................................................................................................45
6.4. Setup Mode ...............................................................................................................45
6.4.1. Password (PASS)..................................................................................................45
6.4.2. Configuration Information (CFG).............................................................................47
6.4.3. Clock (CLK) .........................................................................................................47
6.5. Setup - Range Configuration (RNGE) .............................................................................48
6.5.1. Physical and Analog Output Ranges.........................................................................49
6.5.2. Reporting Range Modes.........................................................................................49
6.5.3. Single Range mode (SNGL)....................................................................................50
6.5.4. Independent Range Mode (IND) .............................................................................50
6.5.5. Auto Range Mode (AUTO) ......................................................................................52
6.5.6. Range Units.........................................................................................................52
6.5.7. Dilution Ratio.......................................................................................................53
6.6. Setup - Internal Variables (VARS) .................................................................................55
6.7. Setup - Diagnostics (DIAG) ..........................................................................................57
6.7.1. Signal I/O ...........................................................................................................58
6.7.2. Analog Output Step Test........................................................................................59
6.7.3. Analog I/O Configuration .......................................................................................60
6.7.3.1. Analog Output Signal Type and Range Selection .................................................61
6.7.3.2. Analog Output Calibration Mode .......................................................................62
6.7.3.3. Manual Analog Output Calibration.....................................................................64
6.7.3.4. Analog Output Offset Adjustment .....................................................................65
6.7.3.5. Current Loop Output Adjustment......................................................................66
6.7.3.6. AIN Calibration ..............................................................................................68
6.7.4. Test Channel Output .............................................................................................68
6.7.5. Optic Test ...........................................................................................................70
6.7.6. Electrical Test ......................................................................................................70
6.7.7. Ozone Generator Override .....................................................................................71
6.7.8. Flow Calibration ...................................................................................................72
6.8. Digital Inputs and Outputs ...........................................................................................72
6.8.1. Status Outputs.....................................................................................................72
6.8.2. Control Inputs......................................................................................................73
6.9. Setup - Communication Ports (COMM) ...........................................................................74
6.9.1. Analyzer ID .........................................................................................................75
6.9.2. COM Port Default Settings .....................................................................................75
6.9.3. COM Port Cable Connections ..................................................................................76
6.9.4. COM2 Configuration..............................................................................................76
6.9.5. DTE and DCE Communication.................................................................................77
6.9.6. COM Port Communication Modes ............................................................................77
6.9.7. COM Port Baud Rate .............................................................................................80
6.9.8. COM Port Testing .................................................................................................80
6.9.9. Ethernet Port Configuration....................................................................................81
6.9.10. Hessen Mode Configuration ..................................................................................84
6.10. Setup - Data Acquisition System (DAS) ........................................................................85
6.10.1. iDAS Structure ...................................................................................................86
6.10.1.1. iDAS Channels .............................................................................................86
6.10.1.2. iDAS Parameters ..........................................................................................87
6.10.1.3. iDAS Triggering Events..................................................................................88
6.10.2. Configuring the iDAS...........................................................................................89
6.10.2.1. Default M200E iDAS Configuration ..................................................................89
6.10.2.2. Viewing iDAS Data and Settings .....................................................................91
6.10.2.3. Editing iDAS Data Channels ...........................................................................92
6.10.2.4. Trigger Events .............................................................................................93
iv 044100102 Rev A