Topcon X14 - Page 133

To Next Page

To Previous Page

Chapter 17 – Troubleshooting Guide

115

Code Fault Action Page

U6905 Unknown machine

type.

Return to main setup

menu, and revise vehicle

setup.

U8505 Factory calibration

not present.

Calibrate compass, wheel

angle sensor and

mounting bias.

67 - 70

TC8 No 12V power

supply to inertial

sensor and modem.

Confirm connections.

Main Page

Default Chapter14
- Table of Contents14
Chapter 1 - Console Overview19
- Introduction19
- Starting the Console19
- Shutting down the Console20
- Using the Console Toolbar21
Chapter 2 - User Interface Description23
- Switching between Setup and Operation Screen23
- Setup Screen Controls23
- Operation Screen Controls26
  - Implement Color Indicators27
- Icon Descriptions27
Chapter 3 - Quick Setup Guide33
- Software Update Instructions33
- Getting Started33
Chapter 4 - Regional and User Settings37
- Setting the Region37
- Setting up the Lightbar40
- Setting up Environment41
- Setting up Map Options42
- Setting Access Level44
Chapter 5 - System Setup45
- Setting Features46
  - Guidance Setup46
  - Implement Setup46
- Setting up GPS47
  - Receiver Setup47
  - Correction Setup48
- Setting up Alarms52
  - Alarm Window Description52
  - Alarms List53
- Setting up Flag Points56
- Setting up Utilities57
Chapter 6 - Vehicle Setup59
- Selecting a Vehicle60
- Creating a New Vehicle60
  - Customizing a Vehicle61
- Setting the Vehicle Geometry61
- Setting up the Steering Controller63
- Selecting the Vehicle Antenna64
Chapter 7 - Implement Setup65
- Selecting an Implement66
- Setting up a New Implement66
- Setting the Implement Geometry67
- Setting up Section Control68
  - Setting Timing68
  - Setting up the Section Switch69
- Setting up the Master Switch69
- Setting up GPS Speed Emulation70
Chapter 8 - Product Setup71
- Setting up the Product Database71
Chapter 9 - Operation Basics73
- Using the Window Toolbar73
- Using the Navigation Window73
- Viewing Guidance74
  - Using View Controls74
- Viewing GPS Information78
- Viewing System Diagnostics79
- Viewing Job Information79
- Monitoring on the Dashboard80
  - Customizing the Dashboard80
- Storing Information about Jobs82
- Recognizing Color and Working Status82
- Understanding Default File Names83
Chapter 10 - Steering Calibrations85
- Calibrating the Compass85
- Calibrating the Wheel Angle Sensor86
- Calibrating the Mounting Bias88
- Dealing with Calibration Errors/Alarms92
Chapter 11 - Field Menu95
- Creating a Client / Farm / Field95
- Selecting a Client / Farm / Field95
- Setting a New Boundary96
- Setting Flag Points101
  - Removing or Changing a Flag Point101
- Unloading a Field102
Chapter 12 - Job Menu103
- Creating a New Job103
  - Setting up Job Regions103
- Selecting an Existing Job104
- Recording Job Details104
- Exporting a Job Report105
- Clearing a Job106
Chapter 13 - Guideline Menu107
- Using Straight Lines Guidelines107
  - Setting AB Lines Manually108
- Using Identical Curve Guidelines109
- Using Center Pivot Guidelines109
- Using Guidelock Guidance Mode110
- Selecting an Existing Guideline110
Chapter 14 - Auto Steering113
- Auto Steer Status113
  - Auto Steer Troubleshooting114
- Tuning Auto Steer116
- Engaging Auto Steer118
- Disengaging Auto Steer119
Chapter 15 - Nudge Menu121
- Using Nudge Options121
- Compensating for GPS Drift121
  - Compensating Correctly for GPS Drift122
  - High Accuracy Correction Sources123
Chapter 16 - Inventory Manager125
- Searching Categories126
- Searching Exporting Jobs126
Chapter 17 - Troubleshooting Guide129
- Common Error Messages129
Chapter 18 - Appendices135
- Appendix A - Glossary135
- Appendix B - Technical Information139
Chapter 19 - Index141

Topcon X14 - Page 133

Table of Contents