Unipulse F371 - 26. CONFORMITY TO EC DIRECTIVES

137 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

22.DIMENSIONS

112

22. DIMENSIONS

 



［ Front ］［ Side ］

［ Rear ］

Panel cut out dimensions

Table of Contents

Default Chapter3
- Safety Precautions3
- Table of Contents5
1 ．Appearance Description12
- Front Panel12
  - Touch Panel Display12
  - Power Lamp12
- Rear Panel13
2 ．Setting Modes16
- F371 Screen Configuration16
- Setting Modes Tree17
- About a Setting Call19
3 ．Connection20
- Power Input Connection20
- Load Cell Connection21
- SI/F Connection22
- External I/O Connection23
  - External Output Connection23
  - External Input Connection23
- RS-232C Interface Connection24
- Voltage Output Connection25
  - Connecting to Cage Clamp Terminal Block26
4 ．Calibration27
- Equivalent Input Calibration Procedure28
- Actual Load Calibration Procedure29
- Zero Calibration30
- Actual Load Calibration31
- Equivalent Input Calibration32
- Digital Offset34
- Increment (this Step May be Omitted if There Is no Change.)35
- Decimal Place36
- Calibration Protection37
- Calibration Value Selection38
  - External Selection of Calibration Value39
- Unit40
5 ．Setting of Functions42
- Digital Zero42
- Digital Filter43
- Analog Filter44
- Display Rate44
- Stability45
- Zero Track46
- Contrast Adjustment47
- Backlight47
- Excitation Voltage47
- Auto Print48
- Hold off Print50
- Parameter Protection50
6 ．Comparison Functions51
- HI Limit/Lo Limit/Hi-HI Limit/Lo-LO Limit52
- Hysteresis53
- Near Zero55
- HI-LO Limit Comparison Mode55
- HI-LO Limit Output Mode56
- Alarm Mode57
7 ．Hold Functions58
- Hold Setting58
- Hold Setting61
  - Minimum Count62
  - Valley Detection Level62
- Hold Setting63
  - Minimum Slope64
  - Interval a and Interval B64
- Hold Setting66
  - Mean Value Sampling Count66
- Hold Operation67
- How to Specify the Hold Detection Period75
8 ．Multi-Hold Function79
- About Changing of the Setting CH80
9 ．Waveform Display81
- Graphic Display Screen81
  - Hold Point Plotting82
  - X-Axis and Y-Axis on the Graph Plotting Screen82
- Graph Plotting83
- Graph Function86
- Interval Time86
- Graph Start Level86
- Level Detection Mode87
- Start Point88
- Y (Load) Start Point and y (Load) End Point89
10 ．Voltage Output（Vol out90
11 ．Screen Lock91
12 ．Event Output at the End of Graph Plotting91
13 ．Rs-232C Interface92
- Communication Specifications92
- RS-232C Interface Setting94
- Communication Modes96
- Communication Format96
14 ．Bcd Data Output(Option)103
- Connector Pin Assignment103
- Logic Change104
- BCD Data Hold104
- Equivalent Circuit104
- Signal Timing105
- BCD Data Update Rate Selection106
- BCD Output Data Selection106
15 ．Rs-485 Communication Interface(Option)107
- Communication Specifications107
- Connection107
- Communication Method110
- Interface Setting111
16 ．D/A Converter(Option)112
- Voltage Zero and Full Scale, Current Zero and Full Scale113
- D/A Output Mode114
- Voltage Output Selection114
- Current Output Selection114
17 ．DC Power Source116
- Error Messages117
19 ．Self-Check and Initialization118
- Self-Check118
- Initialization(All Setting Value Clearances)120
- Password120
20 ．About Japanese/English Display Selection121
21 ．Block Diagram122
22 ．Dimensions123
23 ．Installation in a Panel124
24 ．Specifications125
- Analog Section125
- Digital Section125
- Communication126
- Options126
- External Input and Output127
- General128
- Accessories129
25 ．Setting Item Chart130
26 ．Conformity to Ec Directives134

Related product manuals

Preview: Unipulse F701-C

Unipulse F701-C