1.
Cla
mp
2. Rear brake
lig
ht switch
lead
3.
Positioning tape
4. 0
2
sensor coupler
5. Radiator fan motor coupler
6. Auxiliary DC
jack
7.
Headlight relay
8. Radiator fan motor lead
9. 0
2
sensor
lead
10
. Fr
ame
11. Engine
12. Adapt
er
bracket
13
. Br
ac
ket
A.
Insert t
he
cl
amp
into t
he
long h
ole
in the battery
box.
B. Route the
rear
brake light
sw
i
tc
h lead outside the
wi
re harness bran
ch
to the 0
2
sens
or
lead.
C.
To
the
ECU
co
upl
er
0.
Install the wire harness clamp to the vehicle before
performi
ng
"Q".
To
install the clamp, r
efer
to "Handlebar (front
vi
e\v)".
E.
When
performing t
he
"Q", tu
rn
t
he
handl
eba
r to
th
e
ri
ght and
pos
ition
th
e w
ir
e harness
as
shown in
th
e illust
rat
ion.
F.
Connec
t the o
2
sensor
co
upler,
and
th
en fasten to
th
e bracket. Make
su
re that the top of t
he
co
up
ler
does not pr
otr
ude. It is okay if the cover is
deformed.
G. Fasten the 0
2
sensor lead
wi
th t
he
clamp,
and
th
en install it
on
t
he
bracket.
H. Route the 0
2
se
n
sor
lead and the rear brake li
ght
sw
i
tc
h
lead
t
hr
ough the br
ac
ket guide.
I. Route the
rear
brake light
sw
it
ch lead outside
brake
Hu
id reservoir hose.
J. It does
not
matter whether the 0
2
se
n
so
r l
ead
or
th
e rear brake light switch lead is on
top
(bottom)
in t
he
area shown in
th
e illust
rat
ion.
K. Connect the radiat
or
fan
mo
t
or
co
upl
er
.
L.
In
se
rt
th
e rubber bracket for the headlight relay
so
that it touch
es
t
he
rib of the air scoop stay on the
vehicle.
M. Install the f
use
box
to
the rubber br
ac
ket, and then
insert the r
ubbe
r bracket
so
that it touches the r
ib
of
the air
scoop
st
ay
on
t
he
vehicle.
Make sure that the fuse
box
is not removed
fr
om
th
e rubber br
ac
ke
t.
N. Route the radiat
or
fan mot
or
lead behind t
he
f
use
box.
0 . Route the radiator fan motor lead rear side of
th
e
vehicle respect to t
he
wire harness.
P.
Insert t
he
cl
amp
so
that it touches the rim of t
he
frame.
Q. F
as
ten the grommet of the wire harness
and
main
sw
it
ch l
ead
with the
clamp
at the rear side
of
the
grommet
and
th
e center
of
the positi
on
ing tape.
Point t
he
tip
of
the clamp out
wa
rd, and then
cut
it.
R. Pos
it
ioning tape for t
he
ma
in
sw
it
ch
lead.
S. F
as
ten
th
e 0
2
sensor lead with t
he
hol
der
.
T. Route 0
2
sensor l
ea
d inside to the prot
rus
ion of
th
e adapter bracket.
U. Inside vehicle
CABLE ROUTING
2-56
To Next Page
Loading...
