1. A
ir
induction system hose (air filter case to a
ir
cut-off valve)
2. Air filter case
3. Throttle cables
4. Sta
to
r co
il
assembly lead
5. Speed sensor lead
6. Clamp
7. Positive battery lead
8.
Starter
mo
to
r lead
9. Stator coil lead
10. W
ir
e harness (to rectifier/r
eg
ulator)
11. Gear posit
io
n sensor lead
12. Sidestand sw
it
ch lead
13. Oil level switch lead
14. Boots
15. Clu
tc
h cable
16. Intake air temperature
se
nsor
co
upler
17. Air scoop s
ta
y
18. W
ir
e harness protector
1
9.
Coupler cover
20.
Ma
in switch
coup
ler 1
21
.
Ma
in switch
co
upler 2
22. Sponge
23. Sponge edge
24
. Canister breather hose
A. Ro
ute
the air in
duc
t
io
n system hose (air filter case
to a
ir
cut-off val
ve
) inside the throttle cable.
B.
To
speed sensor
C. Rou
te
the fuel tank drain hose/breather hose out-
side to t
he
wire harnesses.
0. Fasten
th
e sidestand switch lead, stator coil
assembly lead, starter
mo
tor lead, oil level switch
lead. and the speed sensor lead
wit
h the clamp.
T
he
order of the leads does
no
t matter. Align the
cla
mp
w
it
h the tape
on
the starter m
oto
r
le
ad.
Do
not cut off t
he
clamp end and
po
int it forward.
E.
Route the gear position sensor lead inside to t
he
shift arm.
F.
Hose bending edge
G. Align t
he
sidestand swijch lead,
oi
l level switch
lead, fuel tank drain hose, and breather hose with
th
e bending edge
of
the hose, and then install
th
em.
Fa
ce t
he
clamp opening
to
the rearward.
H.
30-50
mm (1.18- 1.97 in)
I. Point the
ti
ps
of
fuel tank drain hose and breat
her
hose as shown in the illustrati
on
.
J. Place the stator
co
il assembly lead so
th
at bare
copper wires
do
not protru
de
from the boots.
K. Route the intake
air
temperat
ur
e sensor
le
ad
above
th
e t
hr
ottle cable in the lrame, and feed it
outside the vehicle through the t
ri
ang
le
ho
le
in t
he
frame.
L. I
ns
tall the clamp to the hole in the air scoop stay.
M. Install
th
e intake a
ir
temperature sensor
coup
ler
on the
ri
b of the air scoop st
ay
.
N. Install
th
e clamp to the hole in the bottom of the
co
upler cover.
0 . Fasten the main switch
co
upler to t
he
co
upler
cover with
th
e cl
am
p.
P.
Ma
ke
sure th
at
the
ma
in sw
it
ch coupler does not
protr
ude
from the sponge edge.
2-58
CABLE ROUTING
Q. Align the wi
re
harness protector with t
he
edge of
t
he
Velcro tape and wrap
it.
However. t
he
tape sur-
face may pr
ot
r
ude
somewhat.
R.
For California on
ly
S. Route t
he
canister brea
th
er hose to the i
ns
ide of
t
he
stator coil asse
mb
ly lead and starter motor
lead, also outside
to
the sidestand switch lead and
t
he
oi
l level switch lead.
T.
It does not matter whether t
he
oil level switch lead
or the sidestand switch lead is on t
op
.
u. It does not
ma
tter whether the f
ue
l tank drain hose
or the br
ea
ther hose is
on
t
op
but
ma
ke
su
re that
these hoses a
re
not twisted each other.
To Next Page
Loading...
