YASKAWA T1000V - Page 417

D.3 UL Standards
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual 417
Standards Compliance
D
Use UL compliant fuses listed in the following table when wiring the main circuit. Branch circuit protection shall be
provided by any of the following:
• Non-time delay Class J, T, or CC fuses sized at 300% of the drive input rating
Note: Exceptional models are A6T6 with 2V0002, A6T15 with 2V0004 or 4V0004, A6T20 with 4V0005, and A6T25 with 4V0007.
• Time delay Class J, T, or CC fuses sized at 175% of the drive input rating
• Time-delay Class RK5 fuses sized at 225% of the drive input rating
Table D.5 Recommended Input Fuse Selection
■ Low Voltage Wiring for Control Circuit Terminals
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local codes for wiring. Use a class
2 (UL regulations) power supply for the control circuit terminal.
Table D.6 Control Circuit Terminal Power Supply
Drive Model CIMR-T
Non-Time Delay Class-T
Fuse Type
(Manufacturer: Ferraz)
600 Vac, 200 kAIR
Fuse Ampere Rating
(A)
Fuse Type
(Manufacturer: Bussmann)
500 Vac, 200 kAIR
Fuse Ampere Rating
(A)
Single-Phase 200 V Class
BV0001 A6T6 6 FWH-25A14F 25
BV0002 A6T10 10 FWH-25A14F 25
BV0003 A6T20 20 FWH-60B 60
BV0006 A6T40 40 FWH-80B 80
BV0010 A6T40 40 FWH-100B 100
BV0012 A6T50 50 FWH-125B 125
Three-Phase 200 V Class
2V0001 A6T3 3 FWH-25A14F 25
2V0002 A6T6 6 FWH-25A14F 25
2V0004 A6T15 15 FWH-25A14F 25
2V0006 A6T20 20 FWH-25A14F 25
2V0010 A6T25 25 FWH-70B 70
2V0012 A6T30 30 FWH-70B 70
2V0020 A6T40 40 FWH-90B 90
2V0030
Not Available
FWH-100B 100
2V0040 FWH-200B 200
2V0056 FWH-200B 200
2V0069 FWH-200B 200
Three-Phase 400 V Class
4V0001 A6T3 3 FWH-40B 40
4V0002 A6T6 6 FWH-40B 40
4V0004 A6T15 15 FWH-50B 50
4V0005 A6T20 20 FWH-70B 70
4V0007 A6T25 25 FWH-70B 70
4V0009 A6T25 25 FWH-90B 90
4V0011 A6T30 30 FWH-90B 90
4V0018
Not Available
FWH-80B 80
4V0023 FWH-100B 100
4V0031 FWH-125B 125
4V0038 FWH-200B 200
Input / Output Terminal Signal Power Supply Specifications
Open Collector Outputs P1, P2, PC Requires class 2 power supply.
Digital Inputs / Outputs
S1, S2, S3, S4, S5, S6, SC,
HC, H1, RP, MP
Use the internal LVLC power supply of the drive. Use class 2 for external
power supply.
Analog Inputs / Outputs +V, A1, A2, AC, AM
Use the internal LVLC power supply of the drive. Use class 2 for external
power supply.