3Com Switch 4800G 24-Port - Page 1156

1156 CHAPTER 90: RRPP CONFIGURATION
[DeviceB-GigabitEthernet1/0/3] quit
[Device B] rrpp domain 1
[Device B-rrpp-domain1] control-vlan 4092
[Device B-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0
[Device B-rrpp-domain1] ring 2 node-mode edge common-port gigabitethernet 1/0/2 edge-port gigabitethernet 1/0/3
[Device B-rrpp-domain1] ring 1 enable
[Device B-rrpp-domain1] ring 2 enable
[Device B-rrpp-domain1] quit
[Device B] rrpp enable
3 Perform the following configuration on Device C:
<Device C> system-view
[DeviceC] interface gigabitethernet 1/0/1
[DeviceC-GigabitEthernet1/0/1] link-delay 0
[DeviceC-GigabitEthernet1/0/1] quit
[DeviceC] interface gigabitethernet 1/0/2
[DeviceC-GigabitEthernet1/0/2] link-delay 0
[DeviceC-GigabitEthernet1/0/2] quit
[DeviceC] interface gigabitethernet 1/0/3
[DeviceC-GigabitEthernet1/0/3] link-delay 0
[DeviceC-GigabitEthernet1/0/3] quit
[Device C] rrpp domain 1
[Device C-rrpp-domain1] control-vlan 4092
[Device C-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0
[Device C-rrpp-domain1] ring 2 node-mode assistant-edge common-port gigabitethernet 1/0/1 edge-port gigabitethernet 1/0/3
[Device C-rrpp-domain1] ring 1 enable
[Device C-rrpp-domain1] ring 2 enable
[Device C-rrpp-domain1] quit
[Device C] rrpp enable
4 Perform the following configuration on Device D:
<Device D> system-view
[DeviceD] interface gigabitethernet 1/0/1
[DeviceD-GigabitEthernet1/0/1] link-delay 0
[DeviceD-GigabitEthernet1/0/1] quit
[DeviceD] interface gigabitethernet 1/0/2
[DeviceD-GigabitEthernet1/0/2] link-delay 0
[DeviceD-GigabitEthernet1/0/2] quit
[Device D] rrpp domain 1
[Device D-rrpp-domain1] control-vlan 4092
[Device D-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 0
[Device D-rrpp-domain1] ring 1 enable
[Device D-rrpp-domain1] quit
[Device D] rrpp enable
5 Perform the following configuration on Device E:
<Device E> system-view
[DeviceE] interface gigabitethernet 1/0/1
[DeviceE-GigabitEthernet1/0/1] link-delay 0
[DeviceE-GigabitEthernet1/0/1] quit
[DeviceE] interface gigabitethernet 1/0/2
[DeviceE-GigabitEthernet1/0/2] link-delay 0
[DeviceE-GigabitEthernet1/0/2] quit
[Device E] rrpp domain 1
[Device E-rrpp-domain1] control-vlan 4092
[Device E-rrpp-domain1] ring 2 node-mode master primary-port gigabitethernet 1/0/1 secondary-port gigabitethernet 1/0/2 level 1
[Device E-rrpp-domain1] ring 2 enable
[Device E-rrpp-domain1] quit
[Device E] rrpp enable
After the configuration, you can use the display command to view RRPP
configuration result.
Configuring
Multi-Domain
Intersecting Ring
Topology
Networking requirements
■ Device A, Device B, Device C and Device D constitute RRPP domain 1, and
Device E, Device F, Device C and Device B constitute RRPP domain 2;
■ VLAN 4090 is the control VLAN of RRPP domain 1, and VLAN 4092 is the
control VLAN of RRPP domain 2;
■ Device A, Device B, Device C and Device D constitute primary ring 1;
■ Device E, Device F, Device C and Device B constitute primary ring 2;