ADCMT 6244 User Manual

6243/44 DC Voltage Current Source/Monitor Operation Manual
Table of Contents
C-2
3.3.6 LIMIT key (Limiter Setting) ...................................................................... 3-8
3.3.7 MENU key (Setting Parameters) ................................................................ 3-8
3.3.7.1 SWEEP (Sweep Parameters) ...................................................................... 3-8
3.3.7.2 TIME (Time Parameters) ........................................................................... 3-10
3.3.7.3 SOURCE (Source Parameters) ................................................................... 3-10
3.3.7.4 MEASURE (Measurement Parameters) ..................................................... 3-11
3.3.7.5 COMPARATOR (Comparison Operation Parameters) ............................. 3-12
3.3.7.6 EXT.SIGNAL (External Control Signal Parameters) ................................ 3-12
3.3.7.7 SYSTEM (System Parameters) .................................................................. 3-14
3.3.7.8 RANDOM MEMORY (Random Memory Settings) ................................. 3-15
3.3.7.9 MEASURE BUFFER (Measurement Buffer Memory) ............................. 3-15
3.3.7.10 PARAMETER SAVE (Saving Parameters) ............................................... 3-16
3.3.7.11 PARAMETER LOAD (Loading Parameters) ............................................ 3-16
3.3.8 MODE key (Source Mode) ........................................................................ 3-17
3.3.9 NULL key (NULL Calculation) ................................................................. 3-17
3.3.10 OPERATE key (Output ON/OFF) ............................................................. 3-17
3.3.11 POLARITY key (Source Polarity) ............................................................. 3-17
3.3.12 RANGE key (Source Range) ...................................................................... 3-18
3.3.13 RECALL key (Measurement Data Recall) ................................................. 3-18
3.3.14 RUN HOLD key (Measurement Free Run/Hold) ...................................... 3-18
3.3.15 START TRIGGER key (Sweep Start, Measurement Trigger) ................... 3-18
3.3.16 STOP key (Sweep Stop) ............................................................................. 3-18
3.3.17 VM/IM key (Measurement Functions) ....................................................... 3-19
3.3.18 VS/IS key (Source Functions) .................................................................... 3-19
3.4 List of Settings .................................................................................................. 3-20
3.4.1 6243 Setting Ranges and Factory Settings ................................................. 3-20
3.4.2 6244 Setting Ranges and Factory Settings ................................................. 3-22
4. PRACTICAL GUIDE FOR MEASUREMENTS ................................ 4-1
4.1 DUT Connection ............................................................................................... 4-1
4.1.1 Precautions for the Output Terminals (Front and Rear Output Terminals) 4-1
4.1.2 Remote Sensing (2-wire/4-wire Connection) ............................................. 4-2
4.1.3 Driving Guard (6243 Only) ........................................................................ 4-5
4.1.4 Oscillation Prevention ................................................................................ 4-5
4.1.4.1 SMU (Source Measurement Unit) Oscillation Prevention ......................... 4-5
4.1.4.2 Oscillation of the Device Itself ................................................................... 4-7
4.1.5 Connection for High-Current Measurement ............................................... 4-8
4.1.6 Connecting to the Fixture 12701A ............................................................. 4-9
4.2 Operation in the DC Source Mode .................................................................... 4-10
4.3 Operation in the Pulse Source Mode ................................................................. 4-12
4.4 Operation in the Sweep Source Mode ............................................................... 4-14
4.4.1 Staircase Sweep .......................................................................................... 4-15
4.4.2 Pulse Sweep ................................................................................................ 4-17
4.4.3 Random Sweep and Random Pulse Sweep ................................................ 4-19
4.4.4 Round-Trip Sweep (Reverse ON) .............................................................. 4-20
4.5 Source Functions ............................................................................................... 4-21
4.5.1 Changing the Source Mode and Source Function ...................................... 4-21
4.5.2 Source value Restrictions ........................................................................... 4-22
4.5.3 Source Range .............................................................................................. 4-23

ADCMT 6244 Specifications

General

Brand	ADCMT
Model	6244
Category	Measuring Instruments
Language	English