Alcatel-Lucent 1643 AMS - 13 Engineering orderwire concepts; Overview; Purpose

To Next Page

To Previous Page

13 13Engineering orderwire concepts

Overview

...................................................................................................................................................................................................................................

Purpose

The purpose of this section is to describe the Engineering orderwire concepts of the

1643 AM.

Contents

Engineering orderwire 13-2

365-312-807R7.2

Issue 4, May 2007

Alcatel-Lucent - Proprietary

See notice on first page

13-1

Main Page

Default Chapter3
- Table of Contents3
About this Information Product19
- Purpose19
- Reason for Reissue19
- Safety Information22
- Intended Audience22
- How to Use this Information Product22
- Conventions Used24
- Related Documentation26
- Related Training27
- Customer Documentation Subnetwork Controller Related27
- Documented Feature Set28
- Intended Use28
- Optical Safety28
- Technical Documentation31
- How to Comment31
1 Safety33
- Overview33
- General Notes on Safety35
- Specific Safety Areas43
2 Getting Started53
- Overview53
- Installing the ITM-CIT53
  - Install ITM-CIT Software53
- Main Menu and Buttons53
  - The ITM-CIT Main Menu53
  - Frequently Used Buttons53
- Login to a NE53
  - Login to a Network Element53
- Change NE Date and Time53
  - Viewing Access Control Parameters77
  - Parameters for Viewing the Access Control Parameters78
- Change the Lock State79
- Change the Inactivity Time82
- Configure or Change a Password85
- Force a Logout88
Management Communication Setup91
- Overview91
- Contents91
  - Example of Dual Stack with Tunneling91
- Concepts93
- Configuring a Data Communication Network (DCN)123
- Procedures Regarding Login into Remote Nes136
- Provision NE Tunnel Information148
5 Equipment Provisioning157
- Overview157
- Provision SNMP Management157
- Concepts159
- Create a Node173
- Provision Slots178
  - Provisioning Slots179
  - Parameters for Provisioning Slots181
- Confirm the MIB182
Retrieve NE Slot Information187
- Viewing NE Slot Information188
- Parameters for Viewing NE Slot Information189
- Overview190
Retrieve Shelf Display190
- Viewing the Shelf Display191
- Parameters for Viewing Shelf Display192
- Overview194
View Hardware Inventory194
- Viewing Hardware Inventory - Shelf195
- Viewing Hardware Inventory - Slot196
- Parameters for Viewing Hardware Inventory198
- Overview199
View SFP Inventory Data199
- Viewing SFP Inventory200
- Parameters for Viewing SFP Inventory Data201
- Overview204
View and Edit Node Details204
- Viewing and Editing Node Details205
- Parameters for Viewing or Editing Node Details207
- Overview209
View and Edit MDI Information209
- Viewing and Editing MDI Information210
- Parameters for Viewing or Editing MDI Information212
- Overview213
View or Edit MDO Information213
- Viewing or Editing MDO Information214
  - Parameters for Viewing or Editing MDO Information216
- Provision Ports217
6 Alarm Management225
- Overview225
- Concepts228
- Alarm Identification239
- Provision Alarm Options252
- Provision Alarm Severity Assignment Profiles (ASAP)256
- Parameters for "ASAP Assignment269
  - Alarm Severity Assignment Profile271
- Alarm Supervision286
- View Historical Data297
7 Timing Provisioning303
- Overview303
- Overview305
- NE Timing306
- Network Synchronization309
- Timing Quality Levels311
- Priorities312
- Example of Network Timing314
- Timing Loop315
- Re-Timing316
- Timing Configuration318
- Provisioning320
8 Traffic Provisioning353
- Overview353
- Cross-Connection Management357
- Path Protection369
  - Overview369
  - Sub-Network Connection Protection (SNCP)370
- Line Protection372
Ethernet Engineering Rules and Guidelines427
- Overview427
- Port Provisioning428
- Quality of Service (Qos) Overview433
- Classification, Queueing, and Scheduling437
- Quality of Service Provisioning446
- Performance Monitoring448
Provision Ethernet over SDH449
- Overview449
- Provisioning Ethernet Services450
Parameters of the Window "View SDH Channel / VCG Information454
- Provisioning a Virtual Switch in Repeater (Promiscuous) Mode455
- Provisioning a Virtual Switch in Spanning Tree Mode457
- Parameters for Provisioning a LAN Unit in Repeater Mode466
- Parameters for Provisioning LAN Unit in Spanning Tree Mode469
Provision MAC Address Tables474
- Overview474
- Provision Static MAC Address Table475
- Provision the MAC Address Learning Mode478
  - Overview481
  - Overview499
9 Traffic Maintenance504
- Overview504
- Overview512
- Overview516
- View the SHDSL Connections517
- Update the SHDSL Connection List518
- Details of the SHDSL Connection List519
- Parameters for Viewing or Editing the SHDSL Connections List520
- View or Edit the NTU Information521
- Overview521
- Update the NTU Information522
- View the NTU Information523
- Edit the NTU Information524
- View or Edit Ntu's General Configuration525
- Remote SHDSL Power Supply (RPS)527
- VC 12 Termination Point Information528
- Update the VC 12 Termination Point Information Window529
- Report the VC 12 Termination Point Information List530
- Edit the VC 12 Termination Point Information List531
- Provisioning the SHDSL on the NT10ETH Modem535
- View SNC Protection536
- Overview536
- Viewing SNC Protection537
- Parameters for Viewing SNC Protection538
- Edit SNC Protection539
- Overview539
- Editing a SNC Protection540
- Parameters for Editing SNC Protection541
- View MSP Protection542
- Overview542
11 MIB Upload/Download545
- Overview545
12 Software Upgrade549
- Overview549
- Overview553
- Overview555
- Overview561
- Parameters for Provisioning Degraded Signal Thresholds575
- Switch SNC Protection576
- Overview576
- Switching SNC Protection577
- Parameters for Switching SNC Protection578
- Switch MSP Protection579
- Overview579
- Switching MSP Protection580
- Parameters for Switching MSP Protection581
10 Performance Monitoring583
- Performance Monitoring583
- Overview583
- Overview585
- Introduction586
- The Performance Monitoring Process589
- Performance Measurements590
- Ethernet Performance Monitoring594
- Available PM Data609
- Configuration of the ITM-CIT617
- Data Storage and Recovery619
- Configure PM on the ITM-CIT622
- Overview622
- Enabling Counter and Setting Thresholds623
- Editing PM Counter Thresholds625
- Parameters for Configuring PM on the ITM-CIT627
- Display PM Data630
- Overview630
- Displaying PM Data631

Alcatel-Lucent 1643 AMS - 13 Engineering orderwire concepts; Overview; Purpose

Table of Contents

Other manuals for Alcatel-Lucent 1643 AMS