Alcatel-Lucent 1643 AMS - Change NE date and time

To Next Page

To Previous Page

Change NE date and time

Overview

...................................................................................................................................................................................................................................

Purpose

The purpose of this procedure is to change the date and time of an NE. The date and

time are important for registration of alarms and PM data.

Contents

Change NE Date and Time 2-19

Parameters for Changing NE Date and Time 2-20

Getting Started

2-18

Alcatel-Lucent - Proprietary

See notice on first page

365-312-807R7.2

Issue 4, May 2007

Main Page

Default Chapter3
- Table of Contents3
About this Information Product19
- Purpose19
- Reason for Reissue19
- Safety Information22
- Intended Audience22
- How to Use this Information Product22
- Conventions Used24
- Related Documentation26
- Related Training27
- Customer Documentation Subnetwork Controller Related27
- Documented Feature Set28
- Intended Use28
- Optical Safety28
- Technical Documentation31
- How to Comment31
1 Safety33
- Overview33
- General Notes on Safety35
- Specific Safety Areas43
2 Getting Started53
- Overview53
- Installing the ITM-CIT53
  - Install ITM-CIT Software53
- Main Menu and Buttons53
  - The ITM-CIT Main Menu53
  - Frequently Used Buttons53
- Login to a NE53
  - Login to a Network Element53
- Change NE Date and Time53
  - Viewing Access Control Parameters77
  - Parameters for Viewing the Access Control Parameters78
- Change the Lock State79
- Change the Inactivity Time82
- Configure or Change a Password85
- Force a Logout88
Management Communication Setup91
- Overview91
- Contents91
  - Example of Dual Stack with Tunneling91
- Concepts93
- Configuring a Data Communication Network (DCN)123
- Procedures Regarding Login into Remote Nes136
- Provision NE Tunnel Information148
5 Equipment Provisioning157
- Overview157
- Provision SNMP Management157
- Concepts159
- Create a Node173
- Provision Slots178
  - Provisioning Slots179
  - Parameters for Provisioning Slots181
- Confirm the MIB182
Retrieve NE Slot Information187
- Viewing NE Slot Information188
- Parameters for Viewing NE Slot Information189
- Overview190
Retrieve Shelf Display190
- Viewing the Shelf Display191
- Parameters for Viewing Shelf Display192
- Overview194
View Hardware Inventory194
- Viewing Hardware Inventory - Shelf195
- Viewing Hardware Inventory - Slot196
- Parameters for Viewing Hardware Inventory198
- Overview199
View SFP Inventory Data199
- Viewing SFP Inventory200
- Parameters for Viewing SFP Inventory Data201
- Overview204
View and Edit Node Details204
- Viewing and Editing Node Details205
- Parameters for Viewing or Editing Node Details207
- Overview209
View and Edit MDI Information209
- Viewing and Editing MDI Information210
- Parameters for Viewing or Editing MDI Information212
- Overview213
View or Edit MDO Information213
- Viewing or Editing MDO Information214
  - Parameters for Viewing or Editing MDO Information216
- Provision Ports217
6 Alarm Management225
- Overview225
- Concepts228
- Alarm Identification239
- Provision Alarm Options252
- Provision Alarm Severity Assignment Profiles (ASAP)256
- Parameters for "ASAP Assignment269
  - Alarm Severity Assignment Profile271
- Alarm Supervision286
- View Historical Data297
7 Timing Provisioning303
- Overview303
- Overview305
- NE Timing306
- Network Synchronization309
- Timing Quality Levels311
- Priorities312
- Example of Network Timing314
- Timing Loop315
- Re-Timing316
- Timing Configuration318
- Provisioning320
8 Traffic Provisioning353
- Overview353
- Cross-Connection Management357
- Path Protection369
  - Overview369
  - Sub-Network Connection Protection (SNCP)370
- Line Protection372
Ethernet Engineering Rules and Guidelines427
- Overview427
- Port Provisioning428
- Quality of Service (Qos) Overview433
- Classification, Queueing, and Scheduling437
- Quality of Service Provisioning446
- Performance Monitoring448
Provision Ethernet over SDH449
- Overview449
- Provisioning Ethernet Services450
Parameters of the Window "View SDH Channel / VCG Information454
- Provisioning a Virtual Switch in Repeater (Promiscuous) Mode455
- Provisioning a Virtual Switch in Spanning Tree Mode457
- Parameters for Provisioning a LAN Unit in Repeater Mode466
- Parameters for Provisioning LAN Unit in Spanning Tree Mode469
Provision MAC Address Tables474
- Overview474
- Provision Static MAC Address Table475
- Provision the MAC Address Learning Mode478
  - Overview481
  - Overview499
9 Traffic Maintenance504
- Overview504
- Overview512
- Overview516
- View the SHDSL Connections517
- Update the SHDSL Connection List518
- Details of the SHDSL Connection List519
- Parameters for Viewing or Editing the SHDSL Connections List520
- View or Edit the NTU Information521
- Overview521
- Update the NTU Information522
- View the NTU Information523
- Edit the NTU Information524
- View or Edit Ntu's General Configuration525
- Remote SHDSL Power Supply (RPS)527
- VC 12 Termination Point Information528
- Update the VC 12 Termination Point Information Window529
- Report the VC 12 Termination Point Information List530
- Edit the VC 12 Termination Point Information List531
- Provisioning the SHDSL on the NT10ETH Modem535
- View SNC Protection536
- Overview536
- Viewing SNC Protection537
- Parameters for Viewing SNC Protection538
- Edit SNC Protection539
- Overview539
- Editing a SNC Protection540
- Parameters for Editing SNC Protection541
- View MSP Protection542
- Overview542
11 MIB Upload/Download545
- Overview545
12 Software Upgrade549
- Overview549
- Overview553
- Overview555
- Overview561
- Parameters for Provisioning Degraded Signal Thresholds575
- Switch SNC Protection576
- Overview576
- Switching SNC Protection577
- Parameters for Switching SNC Protection578
- Switch MSP Protection579
- Overview579
- Switching MSP Protection580
- Parameters for Switching MSP Protection581
10 Performance Monitoring583
- Performance Monitoring583
- Overview583
- Overview585
- Introduction586
- The Performance Monitoring Process589
- Performance Measurements590
- Ethernet Performance Monitoring594
- Available PM Data609
- Configuration of the ITM-CIT617
- Data Storage and Recovery619
- Configure PM on the ITM-CIT622
- Overview622
- Enabling Counter and Setting Thresholds623
- Editing PM Counter Thresholds625
- Parameters for Configuring PM on the ITM-CIT627
- Display PM Data630
- Overview630
- Displaying PM Data631

Alcatel-Lucent 1643 AMS - Change NE date and time

Table of Contents

Other manuals for Alcatel-Lucent 1643 AMS