Anritsu MS9710C - Section 9 Details on Device Messages

9-1
Details on Device Messages
9
9.1 ALIN [Auto Alignment] ............................. 9-2
9.2 ANA [Analysis]......................................... 9-3
9.3 ANAR [Spectrum Analysis Result] .......... 9-6
9.4 AP [Application] ....................................... 9-7
9.5 APR [Application Result] ......................... 9-16
9.6 ARED [Acutual Resolution Data] ............. 9-25
9.7 ARES [Actual Resolution]........................ 9-25
9.8 ATT [Optical Attenuater] .......................... 9-25
9.9 AUT [Auto Measure] ................................ 9-26
9.10 AVS [Sweep Average] ............................. 9-26
9.11 AVT [Point Average] ................................ 9-27
9.12 BKL [Back Light] ...................................... 9-27
9.13 BUZ [Buzzer ON/OFF] ............................ 9-28
9.14 CNT [Center Wavelength] ....................... 9-28
9.15 CPY [Copy] .............................................. 9-29
9.16 CRCL [Condition Recall] ......................... 9-29
9.17 CSAV [Condition Save] ........................... 9-29
9.18 DATE [Date Set] ...................................... 9-30
9.19 DBA [Memory Data A] ............................. 9-30
9.20 DBB [Memory Data B] ............................. 9-31
9.21 DCA [Data Condition Memory A] ............. 9-31
9.22 DCB [Data Condition Memory B] ............. 9-32
9.23 DEL [FD File Delete] ............................... 9-32
9.24 DMA [Memory Data A] ............................ 9-33
9.25 DMB [Memory Data B] ............................ 9-34
9.26 DMD [Display Mode] ............................... 9-35
9.27 DMK [∆ Marker] ....................................... 9-36
9.28 DPS [Dip Search] .................................... 9-37
9.29 DQA [Memory Data A] ............................. 9-38
9.30 DQB [Memory Data B] ............................. 9-38
9.31 DRG [Dynamicrange Mode] .................... 9-39
9.32 EMK [Marker Off] ..................................... 9-39
9.33 ERR [Error] .............................................. 9-39
9.34 ESE1 [Extended Event Status Enable
Register1] ................................................ 9-40
9.35 ESE2 [Extended Event Status Enable
Register2] ................................................ 9-40
9.36 ESE3 [Extended Event Status Enable
Register3] ................................................ 9-40
9.37 ESR1 [Extended Event Status Register1] .... 9-41
9.38 ESR2 [Extended Event Status Register2] .... 9-41
9.39 ESR3 [Extended Event Status Register3] .... 9-41
9.40 FED [Feed] .............................................. 9-42
9.41 FMT [FD Format] ..................................... 9-42
9.42 FOPT [FD File Option] ............................. 9-42
9.43 GCL [Graph Clear] .................................. 9-43
9.44 HEAD [Header] ........................................ 9-43
9.45 ITM [Interval Time] .................................. 9-43
9.46 LCD [Display Color] ................................. 9-44
9.47 LLV [Linear Scale] ................................... 9-45
Section 9 Details on Device Messages
9.48 LOFS [Level Offset] ................................. 9-45
9.49 LOG [Log Scale] ...................................... 9-46
9.50 LVS [Level Scale] .................................... 9-46
9.51 MDM [Modulation Mode] ......................... 9-46
9.52 MKA [Wavelength Marker A] ................... 9-47
9.53 MKB [Wavelength Marker B] ................... 9-47
9.54 MKC [Level Marker C] ............................. 9-48
9.55 MKD [Level Marker D] ............................. 9-49
9.56 MKV [Marker Value Wavelength/
Frequency Select] ................................... 9-50
9.57 MOD [Measure Mode] ............................. 9-50
9.58 MPT [Sumpling (Measureing) Points]...... 9-51
9.59 MSL [Memory Select] .............................. 9-51
9.60 OPT [Light Output] .................................. 9-51
9.61
_______________
.................................. 9-52
9.62 PKC [Peak → Center].............................. 9-52
9.63 PKL [Peak → Level] ................................ 9-52
9.64 PKS [Peak Search] .................................. 9-53
9.65 PWR [Power Monitor] .............................. 9-54
9.66 RCAL [Resolution Calibration] ................. 9-54
9.67 PWRR [Power Monitor Result] ................ 9-55
9.68 RCL [FD File Recall] ................................ 9-55
9.69 RES [Resolution] ..................................... 9-56
9.70 RLV [Reference Level Scale] .................. 9-56
9.71 SAV [FD File Save] ................................. 9-57
9.72 SMT [Smooth] ......................................... 9-57
9.73 SPC [Spectrum]....................................... 9-57
9.74 SPN [Span Wavelength] .......................... 9-58
9.75 SRT [Repeat Sweep] ............................... 9-58
9.76 SSI [Single Sweep] .................................. 9-58
9.77 SST [Sweep Stop] ................................... 9-59
9.78 STA [Start Wavelength] ........................... 9-59
9.79 STO [Stop Wavelength] ........................... 9-59
9.80 TDL [EXT-trigger Delay Time] ................. 9-60
9.81 TDSP [Time & Date Display On/Off] ....... 9-60
9.82 TER [Title Erase] ..................................... 9-60
9.83 TIME [Time Set] ...................................... 9-61
9.84 TLSA [Measure Mode (Adjust to TLS)] ... 9-61
9.85 TLST [Measure Mode (TLS Tracking)] .... 9-62
9.86 TMC [TMKR → Center] ........................... 9-62
9.87 TMK [Trace Marker] ................................ 9-62
9.88 TRM [Terminater] .................................... 9-63
9.89 TSL [Trace Select]................................... 9-64
9.90 TTL [Title] ................................................ 9-64
9.91 VBW [Video Band Width] ........................ 9-65
9.92 WCAL [Wavelength Calibration] .............. 9-65
9.93 WDP [Vacuum/Air Set] ............................ 9-66
9.94 WOFS [Wavelength Offset] ..................... 9-66
9.95 WSS [Setting Wavelength Start and Stop] ... 9-67
9.96 ZMK [Zone Marker] ................................. 9-67