•
The drive has 2 acces s codes , enabling 2 acces s levels to be s et up:
-
PIN code 1 is a public unlock code: 6969.
-
PIN code 2 is an unlock code known only to BLEMO Product Support. It can only be acces sed
in
[E
x
p
ert]
(
EP
r
) m ode.
-
Only one PIN1 or PIN2 code can be us ed, the other m us t rem ain set to
[OFF]
(OFF).
Note:
When the unlock code is entered, the us er acces s code appears.
The following item s are acces s-protected:
•
Return to factory s ettings (
[FACTORY SETTINGS]
(
FCS
-
) m enu.
•
The channels and parameters protected by the
[MY
MENU]
(M
YMn
-
) as well as the m enu its elf.
•
The cus tom display s ettings (
[3.4 DISPLAY CONFIG.]
(dCF-)
m enu).
Code Nam e / De s cription Adjus tment range Factory setting
CS
t
LC
ULC
[State]
[Unlock e d]
(
ULC
)
Information parameter, cannot be modified.
[Lock ed]
(LC): The drive is locked by a password
[Unlock e d]
(ULC): The drive is not locked by a passw ord
COd
[PIN code 1]
[OFF]
(OFF) to 9,999
[OFF]
(OFF)
1st access code. The value
[OFF]
(OFF) indicates that no password has been set
[Unlock ed]
(ULC). The value
[ON]
(On)
indicates that the drive is protected and an access code must be entered in order to unlock it. Once the correct code has been
entered, it remains on the display and the drive is unlocked until the next time the pow er supply is disconnected.
PIN code 1 is a public unlock code: 6969.
COd2
[PIN code 2]
[OFF]
(OFF) to 9,999
[OFF]
(OFF)
This
paramete r
can
only
be
accessed
in
[Expe rt ]
(
EP
r
)
mode.
2nd access code. The value
[OFF]
(OFF) indicates that no passw ord has been set
[Unlocked]
(ULC). The value
[ON]
(On)
indicates that the drive is protected and an access code must be entered in order to unlock it. Once the correct code has been
entered, it remains on the display and the drive is unlocked until the next time the pow er supply is disconnected.
PIN code 2 is an unlock code know n only to BLEMO Product Support.
When
[PIN code 2]
(COd2) is not set to
[OFF]
(OFF), the
[1.2 MONITORING]
(MOn-) menu is the only one visible. Then if
[PIN code 2]
(COd2) is set to
[OFF]
(OFF) (drive unlocked), all menus are visible.
If the display settings are modified in
[3.4 DISPLAY CONFIG.]
(dCF-)
menu, and if
[PIN code 2]
(COd2) is not set to
[OFF]
(OFF), the visibility configured is kept. Then if
[PIN code 2]
(COd2) is set to OFF (drive unlocked), the visibility
configured in
[3.4 DISPLAY CONFIG.]
(dCF-)
menu is kept.
ULr
ULr0
ULr1
[Upload rights]
[Pe rm itted]
(ULr0)
Reads or copies the current configuration to the drive.
[Pe rmitted]
(ULr0):
The current drive configuration can be uploaded to the graphic display terminal or PC Softw are.
[Not allow ed]
(ULr1):
The current drive configuration can only be uploaded to the graphic display terminal or PC Sofw are if
the drive is not protected by an access code or if the correct code has been entered.
dLr
dLr1
dLr3
[Download rights]
[Unlock . drv]
(dLr1)
Writes the current configuration to the drive or dow nloads a configuration to the drive.
[Lock ed drv]
(dLr0):
A configuration file can only be dow nloaded to the drive if the drive is protected by an access code,
w hich is the same as the access code for the configuration to be dow nloaded.
[Unlock . drv]
(dLr1):
A configuration file can be dow nloaded to the drive or a configuration in the drive can be modified if the
drive is unlocked (access code entered) or is not protected by an access code.
[Not allow e d]
(dLr2):
Dow nload not authorized.
[Lock /unlock ]
(dLr3):
Combination of
[Lock e d drv.]
(dLr0)
and
[Unlock . drv]
(dLr1).
To Next Page
