Configuration Mode (ConF)
Factory Settings
Code Nam e / De s cription Factory setting
FCSI
*
InI
CFG1
CFG2
[Config. Source]
[Macro- C on f]
(
InI
)
Choice of source configuration.
If the configuration switching function is configured, it w ill not be possible to access
[Config 1]
(CFG1) and
[Config 2]
(CFG2).
Note:
To load the drive's presettings previously stored (
[Config 1]
(Str1)
or
[Config 2]
(Str2)),
select the source
configuration
[Config. Source ]
(FCSI)
=
[Config 1]
(CFG1) or
[Config 2]
(CFG2) follow ed by a factory setting
[Goto FACTORY SETTINGS]
(GFS) =
[YES]
(YES).
[Macro- C o nf]
(
InI
):
Factory
configuration,
return
to
selected
macro
configuration
[Config 1]
(CFG1): Configuration 1
[Config 2]
(CFG2): Configuration 2
FrY-
ALL
drM
MO
COM
dIS
[PARAMETER GROUP LIST]
Selection of menus to be loaded.
See the multiple selection procedure on page 33 for the integrated display terminal and page 24 for the graphic display terminal.
Note:
In factory configuration and after a return to "factory settings",
[PARAM ETER GROUP LIST]
w ill be empty.
[All]
(ALL): All parameters (the function blocks program w ill also be erased)
[Driv e
config urat io n]
(
drM
):
The
[1
DRIV E
MEN U ]
(
drI-
)
menu
without
[COM M U N IC A TIO N]
(
COM-
).
In
the
[2.4 DISPLAY CONFIG.]
menu,
[Return s td name]
(GSP) page 289 returns to
[No]
(nO).
[M otor param]
(MOt): Motor parameters, see page 297.
The
following
selections
can
only
be
accessed
if
[Conf ig .
Sourc e]
(
FCSI
)
is
set
to
[Macro- C on f .]
(
InI
).
[Com m . m enu]
(COM): The
[COM M UNICATION]
(COM-) menu w ithout either
[Scan. In1 address]
(nMA1) to
[Scan. In8 address]
(nMA8) or
[Scan.Out1 addre s s ]
(nCA1) to
[Scan.Out8 addre s s ]
(nCA8).
[Dis play config.]
(dIS): The
[3.3 M ONITORING CONFIG.]
(MCF-) menu
GFS
*
2 s
nO
YES
[Goto FACTORY SETTINGS]
WARNING
UNANTICIPATED EQUIPMENT OPERATION
Verify that res toring the factory settings is com patible with the type of wiring used.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
It is only possible to revert to the factory settings if at least one group of parameters has previously been selected.
[No]
(nO): No
[Ye s ]
(YES): The parameter changes back to
[No]
(nO) automatically as soon as the operation is complete
SCSI
*
nO
Str0
Str1
Str2
[Save config]
[No]
(nO)
The active configuration to be saved does not appear for selection. For example, if it is
[Config 0]
(Str0),
only
[Config 1]
(Str1)
and
[Config 2]
(Str2)
appear. The parameter changes back to
[No]
(nO) as soon as the operation is
complete.
[No]
(nO): No
[Config 0]
(Str0):
Press and hold dow n the ENT key for 2 s
[Config 1]
(Str1):
Press and hold dow n the ENT key for 2 s
[Config 2]
(Str2):
Press and hold dow n the ENT key for 2 s
These parameters only appear if the corresponding function has been selected in another menu. When the parameters can
also be accessed and adjusted from w ithin the configuration menu for the corresponding function, their description is detailed
in these menus, on the pages indicated, to aid programming.
To change the assignment of this parameter, press the ENT key for 2 s.
Parameters described in this page can be accessed by:
DRI- > CONF > FCS-
2 s
*
To Next Page
Loading...
