Code Nam e / De s cription Unit
(continued)
HMI Passw ord.
If you have lost your code, please contact BLEMO.
CS
t
LC
ULC
[State]
Status of the drive (lock/unlock). Information parameter, cannot be modified.
[Lock ed]
(LC): The drive is locked by a password
[Unlock e d]
(ULC): The drive is not locked by a passw ord
COd
OFF
On
[PIN code 1]
Confidential code.
Enables the drive configuration to be protected using an access code.
When access is locked by means of a code, only the parameters in the
[1.2 M ONITORING]
(MOn-) and
[1.1 SPEED REFERE NC E]
(rEF-)
menus can be accessed. The MODE key can be used to sw itch betw een menus.
Note:
Before entering a code, do not forget to make a careful note of it.
[OFF]
(OFF): No access locking codes.
-
To lock access, enter a code (2 to 9,999). The display can be incremented using the jog dial. Then press ENT.
[ON]
(On)
appears on the screen to indicate that access has been locked.
[ON]
(On): A code is locking access (2 to 9,999).
-
To unlock access, enter the code (incrementing the display using the jog dial) and press ENT. The code remains on the
display and access is unlocked until the next time the drive is turned off. Access will be locked again the next time the drive
is turned on.
-
If an incorrect code is entered, the display changes to
[ON]
(On), and access remains locked.
Access is unlocked (the code remains on the screen).
-
To reactivate locking w ith the same code w hen access has been unlocked, return to
[ON]
(On) using the jog dial and then
press ENT.
[ON]
(On) remains on the screen to indicate that access has been locked.
-
To lock access with a new code w hen access has been unlocked, enter the new code (increment the display using the jog
dial) and then press ENT.
[ON]
(On) appears on the screen to indicate that access has been locked.
-
To clear locking w hen access has been unlocked, return to
[OFF]
(OFF) using the jog dial and then press ENT.
[OFF]
(OFF) remains on the display. Access is unlocked and w ill remain so until the next restart.
COd2
[PIN code 2]
Confidential code 2. Visible if
[3.1 ACCESS LEVEL]
(LAC) is set to
[Expe rt]
(Epr).
OFF
The value
[OFF]
(OFF) indicates that no passw ord has been set
[Unlock ed]
(ULC).
configuration is protected and an access code must be entered in order to unlock it.
Once the correct code has been entered, it remains on the display and the drive is unlocked until the next time the pow er sup
8888
PIN code 2 is an unlock code know n only to BLEMO Product Support.
ULr
ULr0
ULr1
[Upload rights]
[Pe rmitted]
(ULr0):
Means that SoMove or the graphic display terminal can save the w hole configuration (password,
protections, configuration). When the configuration is edited, only the non protected parameters w ill be accessible.
[Not allow ed]
(ULr1):
Means that SoMove or the graphic display terminal cannot save the configuration
dLr
dLr0
dLr3
[Download rights]
[Lock ed drv]
(dLr0):
Locked
drive: means that the configuration can be dow nloaded only in a locked drive w hich configuration
has the same password. If the passwords are different, download is not permitted.
[Unlock . drv]
(dLr1):
Unlocked drive: means that the configuration can be dow nloaded only in a drive w ithout active password
[Not allow e d]
(dLr2):
Not allow ed: the configuration cannot be dow nloaded
[Lock /unlock ]
(dLr3):
Lock. + Not: dow nload is permitted follow ing case 0 or case 1
These parameters only appear if the corresponding function has been selected in another menu. When the parameters can
also be accessed and adjusted from w ithin the configuration menu for the corresponding function, their description is detailed
in these menus, on the pages indicated, to aid programming.
Parameter that can be modified during operation or w hen stopped.
*
To Next Page
Loading...
