EasyManuals Logo

Cisco Catalyst 2950 Software Guide

Cisco Catalyst 2950
376 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #280 background imageLoading...
Page #280 background image
11-14
Catalyst 2950 Desktop Switch Software Configuration Guide
78-11380-03
Chapter 11 Configuring IGMP Snooping and MVR
Understanding Multicast VLAN Registration
Displaying MVR
You can display MVR information for the switch or for a specified interfaces.
Beginning in privileged EXEC mode, use the commands in Table 11-3 to display MVR configuration:
Thisexampleshowstheresultsoftheshow mvr privileged EXEC command:
Switch# show mvr
MVR Running: TRUE
MVR multicast vlan: 1
MVR Max Multicast Groups: 256
MVR Current multicast groups: 256
MVR Global query response time: 5 (tenths of sec)
MVR Mode: compatible
Thisexampleshowstheresultsoftheshow mvr interface privileged EXEC command:
Switch# show mvr interface
Port Type Status Immediate Leave
---- ---- ------- ---------------
Gi0/1 SOURCE ACTIVE/UP DISABLED
Gi0/2 SOURCE ACTIVE/UP DISABLED
Gi0/3 RECEIVER ACTIVE/UP DISABLED
Gi0/4 RECEIVER ACTIVE/UP DISABLED
Gi0/5 RECEIVER ACTIVE/UP ENABLED
Gi0/6 RECEIVER ACTIVE/UP DISABLED
Gi0/7 RECEIVER ACTIVE/UP ENABLED
Gi0/8 RECEIVER ACTIVE/UP DISABLED
Thisexampleshowstheresultsoftheshow mvr interface privileged EXEC command for a specified
interface:
Switch# show mvr interface gigabitethernet0/2
Type: RECEIVER Status: ACTIVE Immediate Leave: DISABLED
Table 11-4 Commands for Displaying MVR Information
show mvr Displays MVR status and values for the switchwhether MVR is enabled or disabled,
the multicast VLAN, the number of multicast groups (always 256 for the Catalyst 2950
switch), the query response time, and the MVR mode.
show mvr interface [interface-id]
[members [vlan vlan-id]]
Displays all MVR interfaces and their MVR configurations.
When a specific interface is entered, displays this information:
TypeReceiver or Source
StatusOne of these:
Active means that the port is part of a VLAN.
Up/Down means that the port is forwarding or nonforwarding.
Inactive means that the port is not part of any VLAN.
Immediate LeaveEnabled or Disabled
If the members keyword is entered, displays all multicast group members on this port or,
if a VLAN identification is entered, all multicast group members on the VLAN.
show mvr members [ip-address] Displays all receiver ports that are members of any IP multicast group or the specified IP
multicast group IP address.

Table of Contents

Other manuals for Cisco Catalyst 2950

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 2950 and is the answer not in the manual?

Cisco Catalyst 2950 Specifications

General IconGeneral
Forwarding Bandwidth8.8 Gbps
Switching Capacity13.6 Gbps
Forwarding Rate6.6 Mpps
Weight3.6 kg
RAM16 MB
Flash Memory8 MB
Operating Humidity10% to 85% non-condensing
Uplink Ports2 x 10/100/1000Base-T
Dimensions4.4 cm x 44.5 cm x 24.2 cm
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesQuality of Service (QoS), VLAN support
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p
Status Indicatorssystem
Operating Temperature0 to 45°C
Ports24 x 10/100 Ethernet ports
MAC Address Table Size8, 192 entries
Power SupplyInternal 100-240V AC, 50-60Hz

Related product manuals