Daedong DSF75GT - Page 218

11
-
3
INDEXDSF75GT
11
-
2
11
-
3
INDEXDSF75GT
11
-
2
A
AbouT SErvIcE ................................................................2-2
A
DjuSTING crAwlEr TENSIoN ...................................8-44
A
DjuSTING DISchArGE coNTrol plATE ..................7-40
A
DjuSTING DuST DISchArGE coNTrol plATE .......7-39
A
DjuSTING EAch bElT lENGTh ...................................8-45
A
DjuSTING GrAIN DISchArGE AmouNT ....................7-27
A
DjuSTING pArkING brAkE pEDAl ............................8-43
A
DjuSTING powEr brAkE lEvEr...............................8-44
A
DjuSTING rEEl poSITIoN ...........................................7-31
A
DjuSTING rEEl roTATING SpEED .............................7-29
A
DjuSTING SIEvE cASE chAFF ....................................7-36
A
DjuSTING ThE rEApING SpEED .................................7-12
A
DjuSTING ThE SIEvE cASE AuXIlIAry plATE po-
SITIoN AND rEplAcING ThE NET ..............................7-36
ADj
uSTING vErTIcAl poSITIoN oF FEEDING Drum ...7-34
A
FTEr complETING INTENDED opErATIoN AND
STorAGE .........................................................................
1-9
A
FTEr DAIly work IS complETED .............................1-27
Al
Arm ...............................................................................4-19
A
NTI-FrEEzE uSE ............................................................8-47
Appl
y GrEASE ................................................................4-15
Appl
y GrEASE ................................................................8-37
Appl
y oIl ..........................................................................4-15
ATT
AchING AND DETAchING covEr ...........................8-21
Au
GEr Drum DrIvE chAIN / rEEl DrIvE chAIN ......8-36
b
bATTEry ...........................................................................8-31
bE
lTS AND rubbEr pArTS .............................................2-4
c
cAuTIoNS DurING rEApING opErATIoN ...................7-23
cA
uTIoNS DurING work ................................................7-4
cA
uTIoNS For AuGEr INSTAllATIoN .........................8-13
cA
uTIoNS For DISchArGE opErATIoN ....................7-26
cA
uTIoNS For vErTIcAl AuGEr INSTAllATIoN ......8-53
c
hANGE DIrEcTIoN DurING work ............................7-19
c
hANGING ........................................................................8-46
c
hANGING ENGINE oIl ...................................................8-47
c
hANGING oIl IN oIl TANk ............................................8-49
c
hANGING rADIATor coolANT ...................................8-46
c
hANGING TrANSmISSIoN cASE FluID ......................8-48
c
hArGE wArNING lAmp .................................................4-8
c
hArGING ........................................................................8-32
c
hEck ...............................................................................8-38
c
hEck bEForE opErATIoN ...........................................1-3
c
hEck bEForE opErATIoN ...........................................5-1
CF100(DSF75GT)_콤바인_영문판_11.indd 2 2017-07-03 오후 2:41:04