DeLaval VMS 2008 - Page 160

206 pages

Save Page as PDF

To Next Page

To Previous Page

Maintenance

DeLaval online cell counter OCC

94897201.pdf2007-12-18

The DeLaval online cell count OCC in manual mode

11. Press the Mode: Online button to set the

DeLaval online cell count OCC to online

mode.

12. The DeLaval online cell count OCC will

now operate automatically.

152(198)

Main Page

Table of Contents3
Delaval Voluntary Milking System VMS11
- Safety Precautions11
- General Description29
- Introduction29
- Operation47
  - General Advice for Operating VMS47
    - Starting, Restarting and Shutting off the Milking Station47
- Restarting the Milking Station after an Emergency Stop48
- Switching between Automatic and Manual Mode49
- Fetch and Start Positions50
- Achieving Successful Teatcup Attachment51
- Working in Manual Mode53
Common Manual Tasks55
- Shutting off the Milking Station56
- Restarting the Milking Station57
- Stopping the Multi-Purpose Arm58
Miscellaneous Tasks59
- Restarting the Milking Station after a Power Failure60
- Shutting down the Hydraulic Pump Unit62
A Complete Manual Milking Procedure64
Stall and Feeding Functions67
Manual Identification68
Attaching Teatcups by Hand71
- Attaching Two Cups at a Time72
Support of Milk Tubes73
Emptying the Receiver and Purging the Milk Lines74
Shutting off the Compressed-Air to the Gates75
- Tank Emptying Process Flow Controlled Cooling (FCC)76
- Tank Emptying FCC: Milk Delivery to Tank Is Stopped Immediately77
- Tank Emptying FCC: Milk Delivery to Tank Is Delayed79
- Tank Emptying: Tank Systems from Other Manufacturers81
- Tank Emptying Process: VMS/IN Cooling Systems83
- Tank Emptying: Delaval Storage Tanks84
- Tank Emptying: Storage Tanks from Other Manufacturers85
Determining Cup and Start Positions87
- Determining the Positions of All Teatcups at the same Time90
- Determining Positions of Individual Teatcups92
- Determining the Position of the Teat Preparation Cup93
- Determining All Teat Positions at the same Time94
- Determining Individual Teat Positions97
- Automatic Determining/Determination of All Teat Positions98
Verification of Determined Positions100
- Verifying the Positions of the Teatcups101
- Searching for Teats102
Contents103
- Detergent Consumption and Concentration104
- Hot Water Supply105
- Alternating Acid and Alkaline Detergent106
- Shelf Life of Detergents107
Starting Cleaning or Rinsing from the Touch Screen108
Viewing the Progress of a Cleaning Process109
- Introduction111
- Overall Performance112
Management Software114
- Vacuum Pump115
- Hydraulic Pump Unit116
- Cleaning Detergent117
- Cleaning of Magazine, Teatcups and Milk Tubes119
- Cleaning of Teat Preparation Cup120
- Cleaning of Camera Window121
- Cleaning of Feeding Module123
- Cleaning of Stall and Floor125
- Change of Filter Sock126
Weekly Maintenance128
- Cleaning of Cow-Detection Sensors129
- Check of Teat Preparation Module130
- Maintenance Every Third Week131
- Check of Oil Recirculation System (ORS)136
- Check of Multi-Purpose Arm138
- Vacuum Pump: Delaval DVP-F139
- Lubrication of Hinges on the Gates140
Milk Refrigeration141
Maintenance Schedule: a Summary142
Milk Sampler145
- Starting a Sampling Sequence147
- Stopping a Sampling Sequence148
Maintenance149
Additional Maintenance151
Delaval Online Cell Counter OCC155
Management Software156
Maintenance157
Delaval Voluntary Milking System VMS161
Types of Alarms162
Meaning and Actions163

DeLaval VMS 2008 - Page 160

Table of Contents

Related product manuals