Troubleshooting
DeLaval voluntary milking system VMS
94897201.pdf2007-12-18
M m Alarm text Type Meaning ActionM m Alarm text Type Meaning Action
3 130 OCC: No water in
funnel or
leakage/stop in
hose or valve
failure
Deviation The OCC can't detect any water Is the water to the OCC turned on (is
the teat cleaner getting water?). Try
press the water button in the cabinet -
is there any water coming into the
funnel? Try run a self test from the
touch screen. If this does not help,
check hoses and valves manually.
3 130 OCC: No water in
funnel or
leakage/stop in
hose or valve
failure
Deviation The OCC can't detect any water Is the water to the OCC turned on (is
the teat cleaner getting water?). Try
press the water button in the cabinet -
is there any water coming into the
funnel? Try run a self test from the
touch screen. If this does not help,
check hoses and valves manually.
3 131 OCC: No milk in
funnel or
leakage/stop in
hose or valve
failure
Deviation The OCC can't detect any milk. Maybe this cow has yield very little
milk, then there might not be enough in
the funnel to perform a measure. If this
is not the case check hoses and valves
manually.
3 131 OCC: No milk in
funnel or
leakage/stop in
hose or valve
failure
Deviation The OCC can't detect any milk. Maybe this cow has yield very little
milk, then there might not be enough in
the funnel to perform a measure. If this
is not the case check hoses and valves
manually.
3 132 OCC: No answer
from the DCC
Deviation The DCC does not answer on the
Alcom bus
Run prime and self test from the touch
screen. Restart MS. If it still does not
work - call service engineer. Is it
powered on? Try "DCC on/off" from the
touch screen, and then just try to read
some parameter to check that it has
come to live. If this does not help
disconnect/connect the power to the
DCC module.
3 132 OCC: No answer
from the DCC
Deviation The DCC does not answer on the
Alcom bus
Run prime and self test from the touch
screen. Restart MS. If it still does not
work - call service engineer. Is it
powered on? Try "DCC on/off" from the
touch screen, and then just try to read
some parameter to check that it has
come to live. If this does not help
disconnect/connect the power to the
DCC module.
3 133 OCC: The DCC
can't count the
cells, some
parameter setting
is wrong
Deviation Some parameter in the DCC is
wrong so that the DCC can not
perform a cell count.
Run prime and self test from the touch
screen. Go through the parameter list
from the touch screen to see if some
parameter is set to an abnormal value
(default values should be available
from helpdesk?)
3 133 OCC: The DCC
can't count the
cells, some
parameter setting
is wrong
Deviation Some parameter in the DCC is
wrong so that the DCC can not
perform a cell count.
Run prime and self test from the touch
screen. Go through the parameter list
from the touch screen to see if some
parameter is set to an abnormal value
(default values should be available
from helpdesk?)
3 134 OCC: Can't clean
the cuvett, it is to
dirty
Deviation The cuvette is to dirty to many
times in a row
Run prime and self test from the touch
screen.If this does not help you need to
manually check the hoses and valves
to find the blockage. If it still does not
work - call for service engineer.
3 134 OCC: Can't clean
the cuvett, it is to
dirty
Deviation The cuvette is to dirty to many
times in a row
Run prime and self test from the touch
screen.If this does not help you need to
manually check the hoses and valves
to find the blockage. If it still does not
work - call for service engineer.
3 135 OCC: Can't
recover, service
needed!
User
notication
The OCC has tried to run two self
test without any luck. It can't
recover from the faults.
Run prime and self test from the touch
screen. Manually check the OCC. Is
the waste bottle empty? Is there any
reagent/hypochlorite in the bottle? Is
the water ok? Replace hoses if
needed. Check all valves (from touch
screen). Try disconnect/connect power
to the OCC. Run prime and self test
from touch screen.
3 135 OCC: Can't
recover, service
needed!
User
notication
The OCC has tried to run two self
test without any luck. It can't
recover from the faults.
Run prime and self test from the touch
screen. Manually check the OCC. Is
the waste bottle empty? Is there any
reagent/hypochlorite in the bottle? Is
the water ok? Replace hoses if
needed. Check all valves (from touch
screen). Try disconnect/connect power
to the OCC. Run prime and self test
from touch screen.
3 136 OCC: Can't get
milk into funnel
User
notication
There is not enough milk in funnel. None required.3 136 OCC: Can't get
milk into funnel
User
notication
There is not enough milk in funnel. None required.
176(198)
To Next Page
Loading...
