Dodge Intrepid - Torque

DESCRIPTION SPECIFICATION
Valve Spring
Free Length—Intake &
Exhaust (Approx.)
45.63 mm
(1.7965 in.)
Spring Force—Intake &
Exhaust (Valve Closed)
249–284 N @ 38.0 mm
(56.0–64.0 lbs. @ 1.4961
in.)
Spring Force—Intake
(Valve Open)
658–721 N @ 29.0 mm
(147.9–162.1 lbs. @
1.1417 in.)
Spring Force—Exhaust
(Valve Open)
614–671 N @ 30.0 mm
(138.0–150.8 lbs. @
1.1811 in.)
Number of Coils—Intake
& Exhaust
7.35
Wire Diameter—Intake &
Exhaust
3.861 mm
(0.1520 in.)
Installed Height—Intake
& Exhaust (Spring seat to
bottom of retainer)
38.0 mm
(1.4961 in.)
Oil Pump
Clearance Over Rotors
(Max.)
0.077 mm
(0.003 in.)
Cover—Out-of-Flat
(Max.)
0.025 mm
(0.001 in.)
Inner & Outer Rotor
Thickness
9.475–9.500 mm
(0.3731–0.3741 in.)
Outer Rotor Clearance
(Max.)
0.39 mm
(0.015 in.)
Outer Rotor Diameter
(Min.)
89.175 mm
(3.5109 in.)
Tip Clearance Between
Rotors (Max.)
0.20 mm
(0.008 in.)
Oil Pressure
(NOTE: At Normal Operating Temperatures)
Pressure @ Curb Idle
Speed*
34.7 kPa Min.
(5 psi) Min.
Pressure @ 3000 RPM 300–724 kPa
(45–105 psi)
*CAUTION: If oil pressure is zero at idle, DO NOT run
engine at 3000 RPM.
TORQUE
DESCRIPTION N·m
Ft.
Lbs.
In.
Lbs.
A/C Compressor to
Engine—Bolts
28 21 —
Camshaft Sprocket—
Bolts
28 — 250
Camshaft Chain
Tensioner (Secondary)—
Bolts
12 — 105
Camshaft Bearing
Cap—Bolts
12 — 105
Connecting Rod
Cap—Bolts
27 +
1
⁄ 4
Turn
20 +
1
⁄ 4
Turn
—
Crankshaft Main Bearing
Cap
—Tie Bolts 28 — 250
—Inner Cap Bolts 20 +
1
⁄ 4
Turn
15 +
1
⁄ 4
Turn
—
—Outer Cap Bolts 27 +
1
⁄ 4
Turn
20 +
1
⁄ 4
Turn
—
Crankshaft Damper—Bolt 170 125 —
Cylinder Head—Bolts (Refer to 9 - ENGINE/
CYLINDER HEAD -
INSTALLATION)
Cylinder Head Cover—
Bolts
12 — 105
Exhaust Manifold—Bolts 23 — 200
Exhaust Manifold Heat
Shield—Bolts
12 — 105
Exhaust Manifold to
Catalytic Converter
V-Band Clamp
11 — 100
Engine Mount Bracket to
Block—Bolts
61 45 —
Engine Mount Isolator—
Nuts
61 45 —
Intake Manifold (Upper
and Lower)—Bolts
12 — 105
Generator Bracket—Bolts 41 30 —
Oil Pan
—Bolts 28 — 250
—Nuts 12 — 105
Oil Pan Drain—Plug 27 20 —
Oil Filter 16 12 —
Oil Pump to Block—Bolts 28 — 250
LH ENGINE 2.7L 9 - 19
ENGINE 2.7L (Continued)