Dynapac CC424HF - Maintenance - Lubricants and Symbols

Maintenance - Lubricants and symbols
ICC424HF-CN1EN2.pdf2012-11-23
Maintenance - Lubricants and symbols
Fluid volumesFluid volumes
DrumDrum
- Drum 14 liters 15 qts- Drum 14 liters 15 qts
- Drum gear 1,5 liters 1.6 qts- Drum gear 1,5 liters 1.6 qts
Hydraulic reservoir 40 liters 42 qtsHydraulic reservoir 40 liters 42 qts
Diesel engineDiesel engine
- oil 11 liters 11.6 qts- oil 11 liters 11.6 qts
- coolant, no cab 21,4 liters 22.6 qts- coolant, no cab 21,4 liters 22.6 qts
- coolant, with cab 23,6 liters 25.0 qts- coolant, with cab 23,6 liters 25.0 qts
Always use high-quality lubricants and the
amounts recommended. Too much grease or
oil can cause overheating, resulting in rapid
wear.
Always use high-quality lubricants and the
amounts recommended. Too much grease or
oil can cause overheating, resulting in rapid
wear.
Other fuel and lubricants are required when
operating in areas with extremely high or
extremely low ambient temperatures. See the
‘Special instructions’ chapter, or consult
Dynapac.
Other fuel and lubricants are required when
operating in areas with extremely high or
extremely low ambient temperatures. See the
‘Special instructions’ chapter, or consult
Dynapac.
DYNAPAC/AtlasCopcoDYNAPAC/AtlasCopco
ENGINE OIL Air temperature -15°C - +50°C
(5°F-122°F)
Shell Rimula R4 L
15W-40, API CH-4 or
equivalent.
AtlasCopco Engine 100,
P/N 5580020624 (5 liters)
ENGINE OIL Air temperature -15°C - +50°C
(5°F-122°F)
Shell Rimula R4 L
15W-40, API CH-4 or
equivalent.
AtlasCopco Engine 100,
P/N 5580020624 (5 liters)
HYDRAULIC FLUID Air temperature -15°C - +50°C
(5°F-122°F)
Shell Tellus S2 V68 or
equivalent.
AtlasCopco Hydraulic
300,
P/N 9106230330 (20 liters)
HYDRAULIC FLUID Air temperature -15°C - +50°C
(5°F-122°F)
Shell Tellus S2 V68 or
equivalent.
AtlasCopco Hydraulic
300,
P/N 9106230330 (20 liters)
Air temperature over +40°C
(104°F)
Shell Tellus S2 V100 or
equivalent.
Air temperature over +40°C
(104°F)
Shell Tellus S2 V100 or
equivalent.
BIOLOGICAL
HYDRAULIC FLUID
When it leaves the factory, the
machine may be filled with
biologically degradable fluid.
The same type of fluid must be
used when changing or topping
up.
BP BIOHYD SE-S 46BIOLOGICAL
HYDRAULIC FLUID
When it leaves the factory, the
machine may be filled with
biologically degradable fluid.
The same type of fluid must be
used when changing or topping
up.
BP BIOHYD SE-S 46
BIOLOGICAL
HYDRAULIC FLUID,
PANOLIN
Air temperature -10°C - +35°C
(14°F-95°F)
When it leaves the factory, the
machine may be filled with
biologically degradable fluid.
The same type of fluid must be
used when changing or topping
up.
PANOLIN HLP Synth 46
(www.panolin.com)
BIOLOGICAL
HYDRAULIC FLUID,
PANOLIN
Air temperature -10°C - +35°C
(14°F-95°F)
When it leaves the factory, the
machine may be filled with
biologically degradable fluid.
The same type of fluid must be
used when changing or topping
up.
PANOLIN HLP Synth 46
(www.panolin.com)
DRUM OIL Air temperature -15°C - +40°C
(5°F-104°F)
Mobil SHC 629 Dynapac Drum Oil 1000,
P/N 4812156456 (5 liters),
P/N 4812156457 (20 liters)
DRUM OIL Air temperature -15°C - +40°C
(5°F-104°F)
Mobil SHC 629 Dynapac Drum Oil 1000,
P/N 4812156456 (5 liters),
P/N 4812156457 (20 liters)
71