Why is HART communication not functioning on my Endress+Hauser Radar?
If HART communication does not function on your Endress+Hauser Radar, consider the following: 1. Install the communication resistor (250 ?) correctly if it is missing or incorrectly installed. 2. Connect the Commubox correctly. 3. Set the selection switch of the Commubox to the HART position.
What to do if my Endress+Hauser Radar device does not respond?
If the Endress+Hauser Radar device does not respond, verify the following: * Ensure the supply voltage matches the value indicated on the nameplate and connect the correct voltage if it doesn't. * Correct the polarity if the supply voltage polarity is wrong. * Ensure proper electrical contact between the cables and terminals.
Why is my Endress+Hauser Radar device measuring incorrectly?
If the Endress+Hauser Radar device measures incorrectly, it might be due to a parametrization error. Check and adjust the parameterization to resolve this issue.
Why is my Endress+Hauser Levelflex FMP55 Measuring Instruments measuring incorrectly?
If your Endress+Hauser Measuring Instrument is measuring incorrectly, it might be due to a parameter configuration error. You should check and correct the parameter configuration.
What causes "Communication error" on Endress+Hauser Radar display?
If a "Communication error" is indicated on the display of your Endress+Hauser Radar when starting the device or connecting the display, electromagnetic interference may be the cause. Check the grounding of the device. Another possible cause is a broken display cable or display plug; in this case, replace the display.
Why CDI communication does not work on Endress+Hauser Radar?
If CDI communication does not work with your Endress+Hauser Radar, check the setting of the COM port on the computer and change it if necessary.
How to fix invisible values on Endress+Hauser Radar display?
If the values on the display of your Endress+Hauser Radar are invisible, it could be due to: * The contrast setting being too weak or too strong. Increase contrast by pressing the appropriate buttons simultaneously or decrease contrast by pressing the corresponding buttons simultaneously. * The plug of the display cable not being connected correctly. Connect the plug correctly. * The display being defective. Replace the display.
Why device cannot be operated via SmartBlue Endress+Hauser Radar?
If the Endress+Hauser Radar device cannot be operated via SmartBlue, it is possible that an incorrect password was entered. Enter the correct password.
What to do if the output current is less than 3.6 mA on Endress+Hauser Radar?
If the output current of your Endress+Hauser Radar is less than 3.6 mA, check the signal cable connection. If the connection is correct, the electronics might be defective and need replacement.
Why Endress+Hauser Radar device does not respond?
If your Endress+Hauser Radar device does not respond, consider the following possible causes: * The supply voltage may not match the value indicated on the nameplate. Ensure you connect the correct voltage. * The polarity of the supply voltage could be wrong. Correct the polarity. * The cables might not be making proper contact with the terminals. Ensure good electrical contact between the cable and the terminal.
General| Housing Material | Aluminum, stainless steel |
|---|---|
| Device Type | Guided radar / TDR |
| Measuring Principle | Time-of-Flight |
| Measuring Range | Up to 30 m (98 ft) |
| Process Pressure | Up to 40 bar (580 psi) |
| Output | 4-20 mA HART, PROFIBUS PA, Foundation Fieldbus |
| Probe Type | Rod, cable |
| Approvals | ATEX, IECEx, FM, CSA |
| Protection Rating | IP66/IP68 |
| Material | Stainless steel, PTFE |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
Explains the scope of the operating instructions and phases of the device lifecycle.
Details safety, electrical, tool, and information symbols used in the document.
Lists related documents and where to find them, including technical information.
Defines key terms and abbreviations used throughout the manual for clarity.
Lists registered trademarks and their owners, essential for legal and brand context.
Outlines qualifications and authorizations required for personnel working with the device.
Specifies the intended application and measured materials for the device, including incorrect use.
Details safety precautions for working on and with the device.
Covers safe operation, device conversions, and repair procedures.
Confirms the device meets state-of-the-art safety standards and legal requirements.
Lists specific safety instructions (XA) applicable based on device approval.
Provides an overview of the Levelflex device design with labeled components.
Describes the procedure for checking received goods for order codes and damage.
Explains methods for identifying the measuring device using nameplate and other means.
Specifies permitted storage temperatures and packaging requirements.
Provides instructions and warnings for safely transporting the device.
Covers general requirements for mounting, including position and probe considerations.
Details the steps for mounting the device, including tools and specific versions.
Lists checks to perform after installation to ensure correct setup.
Covers general connection conditions and terminal assignments.
Provides step-by-step instructions for connecting the device.
Lists checks to perform after electrical connections are made.
Gives a general overview of the available operation modes.
Explains the organization and functionality of the device's operating menu.
Describes the display appearance and symbols.
Introduces HART Device Description files and where to find them.
Explains how measuring values are assigned to HART device variables.
Lists device and system requirements for using SmartBlue commissioning.
Guides through downloading, installing, and performing SmartBlue commissioning.
Emphasizes completing final checks before startup.
Explains how to set the device's operating language.
Details configuration steps for interface measurements, including parameters like DC value.
Describes how to save the envelope curve as a reference for diagnostics.
Covers factory settings and adjustment of the on-site display.
Covers factory settings and adjustment of current outputs for interface measurements.
Describes saving, copying, and restoring device configurations.
Explains methods for securing device settings against unauthorized changes.
Provides a troubleshooting guide for common errors and their solutions.
Explains how diagnostic messages are displayed locally on the device.
Explains how diagnostic events are displayed and managed in operating tools.
Details how to view pending diagnostic messages and their remedies.
Provides a comprehensive list of diagnostic events, short texts, and remedy instructions.
Covers viewing and filtering the history of events.
Lists firmware versions and their associated modifications and documentation.
Provides instructions for cleaning the device exterior.
Details the procedure for cleaning coax probes.
Outlines the repair concept and general guidelines.
Lists important spare parts and how to order them.
Provides information on returning devices for service or calibration.
Covers notes and regulations for device disposal.
Lists accessories directly related to the device itself.
Lists accessories for device communication.
Lists accessories related to device service and configuration.
Describes system components like data managers and barriers.
Lists parameters accessible via the SmartBlue app.
Lists parameters accessible via the local display module.
Lists parameters accessible via an operating tool like FieldCare.
Details the parameters within the Setup menu for device configuration.
Details diagnostic functions and parameters for troubleshooting.
To Next Page
