What to do if my Endress+Hauser Radar device measures incorrectly?
If your Endress+Hauser Radar device is measuring incorrectly, the cause might be a parameterization error. Check and adjust the parameterization to resolve this issue.
Why is HART communication not working on my Endress+Hauser Radar?
If HART communication is not functioning on your Endress+Hauser Radar device, check the following: 1. Ensure the communication resistor (250 ?) is correctly installed. 2. Verify the Commubox is connected correctly. 3. Confirm that the Commubox is switched to HART mode.
Why is my Endress+Hauser Radar device not accessible via SmartBlue?
If your Endress+Hauser Radar device is not accessible via SmartBlue, it could be due to several reasons: * The Bluetooth function might not be enabled on your smartphone or tablet. If this is the case, enable Bluetooth. * The device may already be linked to another smartphone or tablet. Disconnect the device from the other smartphone or tablet. * The Bluetooth module may not be connected. Connect the Bluetooth module.
Why are the values on the display of my Endress+Hauser Levelflex FMP55 invisible?
If the values on the display of your Endress+Hauser Measuring Instruments are invisible, the contrast setting may be too weak or too strong. Try increasing the contrast by pressing the indicated buttons simultaneously, or decreasing it by pressing the indicated buttons simultaneously. Also, ensure that the plug of the display cable is correctly connected. If the issue persists, the display may be defective and need replacement.
How to troubleshoot an Endress+Hauser Levelflex FMP55 device that does not respond?
If your Endress+Hauser Measuring Instruments device does not respond, ensure that the correct supply voltage is connected. Also, check that the cables properly contact the terminals.
What to do if 'Communication error' is indicated on the display of Endress+Hauser Levelflex FMP55 Measuring Instruments?
If you see a "Communication error" on the display of your Endress+Hauser Measuring Instruments when starting the device or connecting the display, it could be due to electromagnetic interference. Check the grounding of the device. It may also be due to a broken display cable or display plug, in which case you should replace the display.
General| Housing Material | Aluminum, stainless steel |
|---|---|
| Device Type | Guided radar / TDR |
| Measuring Principle | Time-of-Flight |
| Measuring Range | Up to 30 m (98 ft) |
| Process Pressure | Up to 40 bar (580 psi) |
| Output | 4-20 mA HART, PROFIBUS PA, Foundation Fieldbus |
| Probe Type | Rod, cable |
| Approvals | ATEX, IECEx, FM, CSA |
| Protection Rating | IP66/IP68 |
| Material | Stainless steel, PTFE |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
Explains the scope of the operating instructions and phases of the device lifecycle.
Details safety, electrical, tool, and information symbols used in the document.
Lists related documents and where to find them, including technical information.
Defines key terms and abbreviations used throughout the manual for clarity.
Lists registered trademarks and their owners, essential for legal and brand context.
Outlines qualifications and authorizations required for personnel working with the device.
Specifies the intended application and measured materials for the device, including incorrect use.
Details safety precautions for working on and with the device.
Covers safe operation, device conversions, and repair procedures.
Confirms the device meets state-of-the-art safety standards and legal requirements.
Lists specific safety instructions (XA) applicable based on device approval.
Provides an overview of the Levelflex device design with labeled components.
Describes the procedure for checking received goods for order codes and damage.
Explains methods for identifying the measuring device using nameplate and other means.
Specifies permitted storage temperatures and packaging requirements.
Provides instructions and warnings for safely transporting the device.
Covers general requirements for mounting, including position and probe considerations.
Details the steps for mounting the device, including tools and specific versions.
Lists checks to perform after installation to ensure correct setup.
Covers general connection conditions and terminal assignments.
Provides step-by-step instructions for connecting the device.
Lists checks to perform after electrical connections are made.
Gives a general overview of the available operation modes.
Explains the organization and functionality of the device's operating menu.
Describes the display appearance and symbols.
Introduces HART Device Description files and where to find them.
Explains how measuring values are assigned to HART device variables.
Lists device and system requirements for using SmartBlue commissioning.
Guides through downloading, installing, and performing SmartBlue commissioning.
Emphasizes completing final checks before startup.
Explains how to set the device's operating language.
Details configuration steps for interface measurements, including parameters like DC value.
Describes how to save the envelope curve as a reference for diagnostics.
Covers factory settings and adjustment of the on-site display.
Covers factory settings and adjustment of current outputs for interface measurements.
Describes saving, copying, and restoring device configurations.
Explains methods for securing device settings against unauthorized changes.
Provides a troubleshooting guide for common errors and their solutions.
Explains how diagnostic messages are displayed locally on the device.
Explains how diagnostic events are displayed and managed in operating tools.
Details how to view pending diagnostic messages and their remedies.
Provides a comprehensive list of diagnostic events, short texts, and remedy instructions.
Covers viewing and filtering the history of events.
Lists firmware versions and their associated modifications and documentation.
Provides instructions for cleaning the device exterior.
Details the procedure for cleaning coax probes.
Outlines the repair concept and general guidelines.
Lists important spare parts and how to order them.
Provides information on returning devices for service or calibration.
Covers notes and regulations for device disposal.
Lists accessories directly related to the device itself.
Lists accessories for device communication.
Lists accessories related to device service and configuration.
Describes system components like data managers and barriers.
Lists parameters accessible via the SmartBlue app.
Lists parameters accessible via the local display module.
Lists parameters accessible via an operating tool like FieldCare.
Details the parameters within the Setup menu for device configuration.
Details diagnostic functions and parameters for troubleshooting.
To Next Page
