Endress+Hauser Proline Prowirl R 200 - Default Chapter; Table of Contents

Proline Prowirl R 200 HART Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Symbols used .......................... 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Communication symbols ........... 6
1.2.4 Tool symbols .................... 7
1.2.5 Symbols for
certain types of information ......... 7
1.2.6 Symbols in graphics ............... 7
1.3 Documentation ........................ 8
1.3.1 Standard documentation ........... 8
1.3.2 Supplementary device-dependent
documentation .................. 8
1.4 Registered trademarks ................... 8
2 Basic safety instructions ............ 9
2.1 Requirements for the personnel ............ 9
2.2 Designated use ........................ 9
2.3 Workplace safety ...................... 10
2.4 Operational safety ..................... 10
2.5 Product safety ........................ 10
2.6 IT security ........................... 11
2.7 Device-specific IT security ................ 11
2.7.1 Protecting access via hardware write
protection ..................... 11
2.7.2 Protecting access via a password .... 11
2.7.3 Access via fieldbus ............... 11
3 Product description ................ 12
3.1 Product design ........................ 12
4 Incoming acceptance and product
identification ..................... 14
4.1 Incoming acceptance ................... 14
4.2 Product identification ................... 14
4.2.1 Transmitter nameplate ........... 15
4.2.2 Sensor nameplate ............... 16
4.2.3 Pressure measuring cells nameplate .. 19
4.2.4 Symbols on measuring device ...... 19
5 Storage and transport ............. 20
5.1 Storage conditions ..................... 20
5.2 Transporting the product ................ 20
5.2.1 Measuring devices without lifting
lugs ......................... 20
5.2.2 Measuring devices with lifting lugs .. 21
5.2.3 Transporting with a fork lift ........ 21
5.3 Packaging disposal ..................... 21
6 Installation ....................... 22
6.1 Installation conditions .................. 22
6.1.1 Mounting position ............... 22
6.1.2 Requirements from environment and
process ....................... 26
6.1.3 Special mounting instructions ...... 27
6.2 Mounting the measuring device ........... 28
6.2.1 Required tools .................. 28
6.2.2 Preparing the measuring device ..... 28
6.2.3 Mounting the sensor ............. 28
6.2.4 Mounting the pressure measuring
unit ......................... 29
6.2.5 Mounting the transmitter of the
remote version ................. 31
6.2.6 Turning the transmitter housing .... 32
6.2.7 Turning the display module ........ 33
6.3 Post-installation check .................. 33
7 Electrical connection .............. 35
7.1 Connection conditions .................. 35
7.1.1 Required tools .................. 35
7.1.2 Connecting cable requirements ..... 35
7.1.3 Connecting cable for remote
version ....................... 36
7.1.4 Terminal assignment ............. 37
7.1.5 Requirements for the supply unit .... 39
7.1.6 Preparing the measuring device ..... 41
7.2 Connecting the measuring device .......... 41
7.2.1 Connecting the compact version ..... 41
7.2.2 Connecting the remote version ..... 43
7.2.3 Connecting the connecting cable for
the pressure measuring cell ........ 47
7.2.4 Ensuring potential equalization ..... 48
7.3 Ensuring the degree of protection .......... 48
7.4 Post-connection check .................. 48
8 Operation options ................. 50
8.1 Overview of operation options ............ 50
8.2 Structure and function of the operating
menu .............................. 51
8.2.1 Structure of the operating menu .... 51
8.2.2 Operating philosophy ............ 52
8.3 Access to the operating menu via the local
display ............................. 53
8.3.1 Operational display .............. 53
8.3.2 Navigation view ................ 54
8.3.3 Editing view ................... 56
8.3.4 Operating elements .............. 58
8.3.5 Opening the context menu ......... 58
8.3.6 Navigating and selecting from list ... 60
8.3.7 Calling the parameter directly ...... 60
8.3.8 Calling up help text .............. 61
8.3.9 Changing the parameters ......... 62