Fagor 8055 M - Page 5

Programming manual
CNC 8055
CNC 8055i
SOFT: V02.2X
·5·
9.7 G81. Drilling canned cycle ........................................................................................... 162
9.7.1 Basic operation ........................................................................................................ 163
9.8 G82. Drilling canned cycle with dwell........................................................................... 165
9.8.1 Basic operation ........................................................................................................ 166
9.9 G83. Deep-hole drilling canned cycle with constant peck............................................ 168
9.9.1 Basic operation ........................................................................................................ 170
9.10 G84. Tapping canned cycle ......................................................................................... 172
9.10.1 Basic operation ........................................................................................................ 174
9.11 G85. Reaming canned cycle........................................................................................ 177
9.11.1 Basic operation ........................................................................................................ 178
9.12 G86. Boring cycle with withdrawal in G00.................................................................... 179
9.12.1 Basic operation ........................................................................................................ 181
9.13 G87. Rectangular pocket canned cycle. ...................................................................... 182
9.13.1 Basic operation ........................................................................................................ 185
9.14 G88. Circular pocket canned cycle .............................................................................. 188
9.14.1 Basic operation ........................................................................................................ 192
9.15 G89. Boring cycle with withdrawal at work feedrate (G01) .......................................... 194
9.15.1 Basic operation ........................................................................................................ 195
9.16 G210. Bore milling canned cycle ................................................................................. 196
9.16.1 Basic operation ........................................................................................................ 198
9.17 G211. Inside thread milling cycle ................................................................................. 199
9.17.1 Basic operation ........................................................................................................ 201
9.18 G212. Outside thread milling cycle .............................................................................. 202
9.18.1 Basic operation ........................................................................................................ 204
CHAPTER 10 MULTIPLE MACHINING
10.1 G60: Multiple machining in a straight line .................................................................... 206
10.1.1 Basic operation ........................................................................................................ 207
10.2 G61: Multiple machining in rectangular pattern ........................................................... 208
10.2.1 Basic operation ........................................................................................................ 210
10.3 G62: Multiple machining in grid pattern ....................................................................... 211
10.3.1 Basic operation ........................................................................................................ 213
10.4 G63: Multiple machining in a circular pattern............................................................... 214
10.4.1 Basic operation ........................................................................................................ 216
10.5 G64: Multiple machining in an arc................................................................................ 217
10.5.1 Basic operation ........................................................................................................ 219
10.6 G65: Machining programmed with an arc-chord.......................................................... 220
10.6.1 Basic operation ........................................................................................................ 221
CHAPTER 11 IRREGULAR POCKET CANNED CYCLE
11.1 2D pockets ................................................................................................................... 225
11.1.1 Drilling operation ...................................................................................................... 228
11.1.2 Roughing operation.................................................................................................. 229
11.1.3 Finishing operation................................................................................................... 232
11.1.4 Profile programming syntax ..................................................................................... 234
11.1.5 Profile intersection.................................................................................................... 235
11.1.6 Profile programming syntax ..................................................................................... 239
11.1.7 Errors ....................................................................................................................... 241
11.1.8 Programming examples ........................................................................................... 243
11.2 3D pockets ................................................................................................................... 246
11.2.1 Roughing operation.................................................................................................. 250
11.2.2 Semi-finishing operation........................................................................................... 253
11.2.3 Finishing operation................................................................................................... 255
11.2.4 Geometry of the contours or profiles........................................................................ 258
11.2.5 Profile programming syntax ..................................................................................... 259
11.2.6 Composite 3D profiles.............................................................................................. 264
11.2.7 Profile stacking......................................................................................................... 267
11.2.8 Profile programming syntax ..................................................................................... 268
11.2.9 Programming examples ........................................................................................... 270
11.2.10 Errors ....................................................................................................................... 282
CHAPTER 12 PROBING
12.1 Probing (G75, G76)...................................................................................................... 286
12.2 Probing canned cycles................................................................................................. 287
12.3 PROBE 1. Tool length calibrating canned cycle .......................................................... 288
12.3.1 Calibrate the length or measure the length wear of a tool. ...................................... 290
12.3.2 Calibrate the radius or measure the radius wear of a tool ....................................... 293
12.3.3 Measure or calibrate the tool radius wear and tool length wear............................... 295
12.4 PROBE 2. Probe calibration canned cycle. ................................................................. 298
12.4.1 Basic operation ........................................................................................................ 300