Fagor 8055 M - Page 6

·6·
Programming manual
CNC 8055
CNC 8055i
SOFT: V02.2X
12.5 PROBE 3. Surface measuring canned cycle ............................................................... 302
12.5.1 Basic operation ........................................................................................................ 304
12.6 PROBE 4. Outside corner measuring canned cycle.................................................... 306
12.6.1 Basic operation ........................................................................................................ 307
12.7 PROBE 5. Inside corner measuring canned cycle....................................................... 309
12.7.1 Basic operation ........................................................................................................ 310
12.8 PROBE 6. Angle measuring canned cycle .................................................................. 312
12.8.1 Basic operation ........................................................................................................ 313
12.9 PROBE 7. Corner and angle measuring canned cycle................................................ 315
12.9.1 Basic operation (measuring an outside corner) ....................................................... 316
12.9.2 Basic operation (measuring an inside corner) ......................................................... 318
12.10 PROBE 8. Hole measuring cycle................................................................................. 320
12.10.1 Basic operation ........................................................................................................ 321
12.11 PROBE 9. Boss measuring cycle ................................................................................ 323
12.11.1 Basic operation ........................................................................................................ 324
12.12 PROBE 10. Rectangular part centering canned cycle................................................. 326
12.12.1 Basic operation ........................................................................................................ 328
12.13 PROBE 11. Circular part centering canned cycle........................................................ 329
12.13.1 Basic operation ........................................................................................................ 331
12.14 PROBE 12. Tabletop probe calibration........................................................................ 332
CHAPTER 13 HIGH-LEVEL LANGUAGE PROGRAMMING
13.1 Lexical description ....................................................................................................... 337
13.2 Variables...................................................................................................................... 339
13.2.1 General purpose parameters or variables ............................................................... 340
13.2.2 Variables associated with tools................................................................................ 342
13.2.3 Variables associated with zero offsets..................................................................... 345
13.2.4 Variables associated with function G49 ................................................................... 347
13.2.5 Variables associated with machine parameters....................................................... 349
13.2.6 Variables associated with work zones ..................................................................... 350
13.2.7 Variables associated with feedrates ........................................................................ 351
13.2.8 Variables associated with coordinates..................................................................... 353
13.2.9 Variables associated with electronic handwheels.................................................... 356
13.2.10 Variables associated with feedback......................................................................... 358
13.2.11 Variables associated with the main spindle ............................................................. 359
13.2.12 Variables associated with the second spindle ......................................................... 362
13.2.13 Variables associated with the live tool ..................................................................... 365
13.2.14 PLC related variables............................................................................................... 366
13.2.15 Variables associated with local parameters............................................................. 368
13.2.16 Sercos variables ...................................................................................................... 369
13.2.17 Software & hardware configuration variables .......................................................... 370
13.2.18 Variables associated with telediagnosis .................................................................. 373
13.2.19 Operating-mode related variables............................................................................ 376
13.2.20 Other variables......................................................................................................... 380
13.3 CONSTANTS............................................................................................................... 389
13.4 Operators..................................................................................................................... 390
13.5 Expressions ................................................................................................................. 392
13.5.1 Arithmetic expressions............................................................................................. 392
13.5.2 Relational expressions............................................................................................. 393
CHAPTER 14 PROGRAM CONTROL INSTRUCTIONS
14.1 Assignment instructions............................................................................................... 396
14.2 Display instructions...................................................................................................... 397
14.3 Enable-disable instructions.......................................................................................... 398
14.4 Flow control instructions .............................................................................................. 399
14.5 Subroutine instructions ................................................................................................ 401
14.5.1 Calls to subroutines using G functions..................................................................... 405
14.6 Probe related instructions ............................................................................................ 406
14.7 Interruption-subroutine instructions ............................................................................. 407
14.8 Program instructions.................................................................................................... 408
14.9 Kinematics related instructions .................................................................................... 411
14.10 Screen customizing instructions .................................................................................. 412