Fuji Electric FRENIC MEGA G2 Series - Page 9

v
[ 2 ] Motor protection with thermistor ............................................................................................. 4-38
4.9 Setting function codes when switching from a conventional model ................................................. 4-39
4.9.1 Switching from FRENIC-MEGA (G1S) ........................................................................................ 4-39
[ 1 ] Copying function codes using the keypad .............................................................................. 4-39
[ 2 ] Entering function codes directly from the keypad ................................................................... 4-39
[ 3 ] Entering function codes from PC Loader ................................................................................ 4-40
4.9.2 Switching from FRENIC5000G11S/P11S or FRENIC5000G9S/P9S ........................................... 4-40
4.10 Operation Check .............................................................................................................................. 4-41
4.10.1 Test run procedure ..................................................................................................................... 4-41
4.10.2 Check points during a test run ................................................................................................... 4-41
4.10.3 Adjusting the function code for motor control ............................................................................. 4-42
4.11 Selecting a Frequency Command Source ....................................................................................... 4-44
4.11.1 Setting the frequency from the keypad....................................................................................... 4-44
4.11.2 Setting the frequency with an external potentiometer (variable resistor) .................................... 4-45
4.11.3 Setting the frequency with multistep frequency selection (1 speed, 2 speed, etc.) .................... 4-46
4.12 Selecting a Run Command Source ................................................................................................. 4-47
4.12.1 Setting run commands from the keypad ..................................................................................... 4-47
4.12.2 Setting run commands with external signals (terminal [FWD, [REV]) ........................................ 4-47
Chapter 5 FUNCTION CODES
5.1 Function Codes Overview .................................................................................................................. 5-1
5.2 Function Code Tables ........................................................................................................................ 5-2
5.2.1 Supplementary note ...................................................................................................................... 5-2
5.2.2 Function code tables ..................................................................................................................... 5-4
[ 1 ] F codes: Fundamental functions ............................................................................................... 5-4
[ 2 ] E codes: Extension Terminal Functions (terminal functions) ..................................................... 5-8
[ 3 ] C codes: Control Functions of Frequency (Control function) .................................................. 5-16
[ 4 ] P codes: Motor 1 Parameters (Motor 1 parameters) ............................................................... 5-18
[ 5 ] H codes: High Performance Functions (High level functions) ................................................. 5-20
[ 6 ] A codes: Motor 2 Parameters (Motor 2 parameters) ............................................................... 5-26
[ 7 ] b codes: Motor 3 Parameters (Motor 3 parameters) ............................................................... 5-29
[ 8 ] r codes: Motor 4 Parameters (Motor 4 parameters) ................................................................ 5-31
[ 9 ] J codes: Application Functions 1 (Application function 1) ....................................................... 5-33
[ 10 ] d codes: Application Functions 2 (Application functions 2) ..................................................... 5-36
[ 11 ] U codes: Application Functions 3 (Customizable logic) .......................................................... 5-43
[ 12 ] y codes: LINK Functions (Link functions) ................................................................................ 5-48
[ 13 ] o codes: Option Functions (Option functions) ......................................................................... 5-50
[ 14 ] K codes: Keypad functions (Keypad functions) ...................................................................... 5-53
5.3 Description of Function Codes ......................................................................................................... 5-66
5.3.1 F codes (Fundamental functions) ................................................................................................ 5-66
[ 1 ] Setting the frequency with the keypad (F01 = 0 (factory default) or 8) ................................... 5-68
[ 2 ] Setting the frequency with analog input (F01 = 1 to 3, 5, 6) ................................................... 5-69
[ 3 ] Frequency setting by digital input signal “UP”/“DOWN” (F01=7) ............................................ 5-76
[ 4 ] Frequency setting using digital input (option DIO interface card) (F01 = 11) .......................... 5-77
[ 5 ] Frequency setting using pulse train input (F01 = 12) .............................................................. 5-78
5.3.2 E codes (Extension terminal functions) ..................................................................................... 5-136
5.3.3 C codes (Control functions) ....................................................................................................... 5-190
5.3.4 P codes (Motor 1 parameters) ................................................................................................... 5-201
5.3.5 H codes (High performance functions) ...................................................................................... 5-212
[ 1 ] Measuring the capacitance of DC link bus capacitor in comparison
with initial one at shipment .................................................................................................... 5-233
[ 2 ] Measuring the capacitance of DC link bus capacitor under ordinary
operating conditions at power shutdown ............................................................................... 5-234