Fujitsu Primergy RX300 S3 User Manual

14
Chapter1 Overview
1.1 RX300 S3
This server has the following features.
■ High Reliability
●
Advanced Memory Protection Function
The server supports the Chipkill function using PC2-4200F (DDRII 533) compliant memory (Fully
Buffered DIMM). Also, memory mirroring function is supported to enable data recovery in the event of
a memory error.
● Disk Array System Configuration
A disk array system (RAID0/1/5/10) can be configured using the onboard array controller MegaRAID
SAS 300-8E ROMB (installed as standard).
● Redundant Function
The hard disk units, power supply units, and system fans support the redundant function.
A failed hard disk unit can be replaced or repaired without turning off the server and peripheral devices
(a hot plug is supported in configurations other than RAID0).
Adding an optional power supply unit enables the redundant function.
● PCI Slots for Hot Plug Function
When the standard card slots are used, PCI slot 3 and 4 are the slots for a hot-plug.
An expansion card can be replaced without turning off the server and peripheral devices when the
expansion card fails (only for Windows Server 2003).
● Hardware and Software Designed for Data Security
The locks on the rack and security (password) setting in the BIOS Setup Utility protect hardware and
data assets in the server against theft, ensuring data security with high reliability.
● Proactive Fan Function
When a fan fails or the ambient temperature rises, the system fan speed is increased automatically to
avoid increase in temperature in the server, ensuring stable server operation.
● Remote Management Control Function
This server has a function of the onboard remote service board. By using the Remote Management
Control function, you can use the Web interface to power on/off or reset the server (remote control
function) and to monitor the server.
For details, refer to "Appendix D Remote Management Controller" (
pg.302).
● High Reliability Tools
High reliability tools offer stable system operation. For information about high reliability tools, refer to
"1.2.2 High Reliability Tools" (
pg.20).

Fujitsu Primergy RX300 S3 Specifications

General

Tcase	78 °C
Bus type	FSB
FSB Parity	Yes
Processor cache	4 MB
Processor cores	2
Processor model	5080
Processor series	Intel Xeon 5000 Series
Processor socket	LGA 771 (Socket J)
Processor threads	4
Processor codename	Dempsey
Motherboard chipset	Intel® 5000P
Processing Die size	162 mm²
Processor frequency	3.73 GHz
Processor cache type	L2
Processor lithography	65 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	1066 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	130 W
Processor core voltage (AC)	1.25 - 1.40 V
CPU multiplier (bus/core ratio)	14
Number of Processing Die Transistors	376 M
Maximum graphics card memory	8 MB
Memory slots	8
Internal memory	2 GB
Internal memory type	DDR2-SDRAM
Maximum internal memory	32 GB
Memory layout (slots x size)	2 x 1 GB
Networking features	Ethernet/Fast Ethernet/Gigabit Ethernet
Expansion slots	1 x PCIe x8, 2 x PCIe x4, 2 x PCI-X
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	56 dB
Chassis type	Rack (2U)
Compatible operating systems	Windows Server 2003, Novell SUSE Linux Enterprise Server, Red Hat Enterprise Linux, VMware ESX
I/O ports	8 x SAS
Power supply	600 W
Power requirements	100 - 240V, 50/60 Hz
Operating temperature (T-T)	10 - 35 °C
Safety	IEC 60950-1, EN 60950-1
Electromagnetic compatibility	EN 55 022 A, EN 55024, EN 61000-3-2 / -3-3
RAID levels	1, 5, 10, 50
Processor ARK ID	27213

Weight and Dimensions

Depth	785 mm
Width	483 mm
Height	86 mm
Weight	25000 g