Fujitsu Primergy RX300 S3 User Manual

266
Chapter 9 Operation and Maintenance
9.2.3 Software Troubleshooting
This section explains software related troubleshooting. For troubles during OS installation or system
operation, refer to the following contents.
■ Trouble at a ServerStart Startup
●
After a boot from the ServerStart CD-ROM, nothing is displayed on the
screen.
This problem may occur if the hard disk drive still contains previous information. In that case, this
problem will occur when the Windows Server 2003 Installation CD-ROM is inserted.
To eliminate this problem, delete all data inthe hard disk drive and start up ServerStart. For deleting data,
refer to "MegaRAID SAS User’s Guide" in "Array Controller Document & Tool CD".
■ Trouble during OS Installation
●
Automatic logon is not performed during Windows 2000 setup.
During OS installation, ServerStart installs applications and hardware utilities supplied with the OS.
Installation and subsequent restart and logon are performed automatically as necessary. In rare cases,
however, automatic logon is not performed and the logon window appears. In this window, use the user
name and password you have set before starting installation. After logon, the setup procedures are
continued.
● Automatic installation stopped at an entry screen during Active Directory
configuration.
If automatic installation has stopped during Active Directory configuration, check the error message
first. Automatic installation can stop when the password is required, such as when registration in DNS
fails. Check the environment and continue the installation manually. If the problem is not solved, click
[Cancel] and after the OS installation, manually configure Active Directory.
If you have continued the Active Directory installation wizard manually, the following message appears
when the installation wizard closes.
When this message appears, click [Restart] to continue the installation.
"You must restart Windows to make the settings in the Active
Directory installation wizard effective."

Fujitsu Primergy RX300 S3 Specifications

General

Tcase	78 °C
Bus type	FSB
FSB Parity	Yes
Processor cache	4 MB
Processor cores	2
Processor model	5080
Processor series	Intel Xeon 5000 Series
Processor socket	LGA 771 (Socket J)
Processor threads	4
Processor codename	Dempsey
Motherboard chipset	Intel® 5000P
Processing Die size	162 mm²
Processor frequency	3.73 GHz
Processor cache type	L2
Processor lithography	65 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	1066 MHz
Processor operating modes	64-bit
ECC supported by processor	No
Thermal Design Power (TDP)	130 W
Processor core voltage (AC)	1.25 - 1.40 V
CPU multiplier (bus/core ratio)	14
Number of Processing Die Transistors	376 M
Maximum graphics card memory	8 MB
Memory slots	8
Internal memory	2 GB
Internal memory type	DDR2-SDRAM
Maximum internal memory	32 GB
Memory layout (slots x size)	2 x 1 GB
Networking features	Ethernet/Fast Ethernet/Gigabit Ethernet
Expansion slots	1 x PCIe x8, 2 x PCIe x4, 2 x PCI-X
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	56 dB
Chassis type	Rack (2U)
Compatible operating systems	Windows Server 2003, Novell SUSE Linux Enterprise Server, Red Hat Enterprise Linux, VMware ESX
I/O ports	8 x SAS
Power supply	600 W
Power requirements	100 - 240V, 50/60 Hz
Operating temperature (T-T)	10 - 35 °C
Safety	IEC 60950-1, EN 60950-1
Electromagnetic compatibility	EN 55 022 A, EN 55024, EN 61000-3-2 / -3-3
RAID levels	1, 5, 10, 50
Processor ARK ID	27213

Weight and Dimensions

Depth	785 mm
Width	483 mm
Height	86 mm
Weight	25000 g