Hioki RM3542 - Page 125

9.6 Message List
119
9
Message Data Contents Description
Ref
page
Delimiter (Terminator)
:SYSTem:TERMinator
0/ 1
Sets and queries the GP-IB command
delimiter.
135
:SYSTem:TERMinator?
[0/ 1]
System Function
:SYSTem:DATE
<Year>,<Month>,<Day>
Sets and queries the system date. 135
:SYSTem:DATE?
[<Year>,<Month>,<Day>]
:SYSTem:TIME
<Hours>,<Minutes>,<Sec-
onds>
Sets and queries the system time. 135
:SYSTem:TIME?
[<Hours>,<Minutes>,<Sec-
onds>]
:SYSTem:BACKup
Backs up measurement settings. 135
:SYSTem:SETMonitor
1/ 0/ ON/ OFF
Sets and queries the Settings Monitor
function.
136
:SYSTem:SETMonitor?
[ON/ OFF]
:SYSTem:SETMonitor:ORDer
1/ 2
Sets and queries the 1st/2nd stage
setting conditions (Settings Monitor
function)
136
:SYSTem:SETMonitor:ORDer?
[1/ 2]
:SYSTem:SETMonitor:ALLowance
0 to 9.999 (%)
Sets and queries the tolerance range
(Settings Monitor function).
136
:SYSTem:SETMonitor:ALLowance?
[0 to 9.999]
:SYSTem:LOCal
Enables the local control state. 136
:SYSTem:DATAout
1/ 0/ ON/ OFF
Sets and queries measurement-syn-
chronized data output.
136
:SYSTem:DATAout?
[ON/ OFF]
:SYSTem:FORMat
ASCii/ BINary
Sets and queries the measurement
data format.
137
:SYSTem:FORMat?
[ASCII/ BINARY]
:SYSTem:4WCHeck
1/ 0/ ON/ OFF
Sets and queries probe short-circuit
detection.
137
:SYSTem:4WCHeck?
[ON/ OFF]
:SYSTem:4WCHeck:TIME
0.001 to 0.1
Sets and queries probe short-circuit
detection time.
137
:SYSTem:4WCHeck:TIME?
[0.001 to 0.1]
:SYSTem:RETRy
1/ 0/ ON/ OFF
Enables the measurement retry func-
tion.
137
:SYSTem:RETRy?
[ON/ OFF]
:SYSTem:RETRy:TIME
0.001 to 0.05 (seconds)
Sets and queries the retry interval. 137
:SYSTem:RETRy:TIME?
[0.001 to 0.05]
:SYSTem:RESet
Executes a system reset. 137
Trigger
:INITiate:CONTinuous
1/ 0/ ON/ OFF
Sets and queries continuous measure-
ment.
139
:INITiate:CONTinuous?
[ON/ OFF]
:INITiate[:IMMediate]
Initiates the trigger wait state. 139
:TRIGger:SOURce
IMMediate/ EXTernal
Sets and queries the trigger source. 139
:TRIGger:SOURce?
[IMMEDIATE/ EXTERNAL]
:TRIGger:DELay1
0 to 0.100
Sets and queries Trigger Delay 1 time. 140
:TRIGger:DELay1?
[0 to 0.100]
:TRIGger:EDGE
RISE/ FALL
Sets and queries trigger (falling (ON)/
rising (OFF)) edge logic.
140
:TRIGger:EDGE?
Notes:
• < >: contents of the data portion.
• [ ]: Response data