12
SET MODE
12-4
Offset Freq (Default: 0�600�00*)
[MENU] > SET > DUP/TONE��� > Offset Freq
Sets the frequency offset for Duplex (repeater)
operation to between 0�000�00 and 59�995�00 MHz�
L Push [VFO/MHz] to select the 1 MHz tuning step�
L The Duplex shift direction (DUP–/DUP+) (p� 11-4) or the
tuning step is set in the Quick Menu window�
L When the DR function is ON, editing is disabled�
* The default value may differ, depending on the frequency
band (selected as the MAIN band before entering the
MENU screen) and the transceiver version�
Repeater Tone (Default: 88�5)
[MENU] > SET > DUP/TONE��� > Repeater Tone
Selects a repeater tone frequency for repeater access
and other functions�
You can select 50 tone frequencies (67�0 ~ 254�1 Hz)�
TSQL Freq (Default: 88�5)
[MENU] > SET > DUP/TONE��� > TSQL Freq
Selects a CTCSS tone frequency for the Tone Squelch
function�
You can select 50 tone frequencies (67�0 ~ 254�1 Hz)�
• Selectable Repeater Tone/TSQL frequencies
(Unit: Hz)
67�0 88�5 114�8 151�4 177�3 203�5 250�3
69�3 91�5 118�8 156�7 179�9 206�5 254�1
71�9 94�8 123�0 159�8 183�5 210�7
74�4 97�4 127�3 162�2 186�2 218�1
77�0 100�0 131�8 165�5 189�9 225�7
79�7 103�5 136�5 167�9 192�8 229�1
82�5 107�2 141�3 171�3 196�6 233�6
85�4 110�9 146�2 173�8 199�5 241�8
Tone Burst (Default: OFF)
[MENU] > SET > DUP/TONE��� > Tone Burst
Turns the Tone Burst function ON or OFF in the FM
mode when using the Tone Squelch function�
• OFF: When you transmit a signal that superimposes
the CTCSS tone, the other station may hear
a short burst of noise from their receiver, just
after you stop transmitting�
• ON:
When you transmit a signal that superimposes
the CTCSS tone, the function mutes the noise
from being heard in the other station’s receiver�
DTCS Code (Default: 023)
[MENU] > SET > DUP/TONE��� > DTCS Code
Selects a DTCS (both encoder/decoder) code for the
DTCS Squelch�
You can select a total of 104 codes (023 ~ 754)�
• Selectable DTCS codes
023 072 152 244 311 412 466 631
025 073 155 245 315 413 503 632
026 074 156 246 325 423 506 654
031 114 162 251 331 431 516 662
032 115 165 252 332 432 523 664
036 116 172 255 343 445 526 703
043 122 174 261 346 446 532 712
047 125 205 263 351 452 546 723
051 131 212 265 356 454 565 731
053 132 223 266 364 455 606 732
054 134 225 271 365 462 612 734
065 143 226 274 371 464 624 743
071 145 243 306 411 465 627 754
DTCS Polarity (Default: Both N)
[MENU] > SET > DUP/TONE��� > DTCS Polarity
Selects the DTCS polarity to use for transmitting (TX)
and receiving (RX)�
• Both N: Normal polarity is used for both TX and RX�
• TN-RR: Normal polarity is used for TX, Reverse
polarity for RX�
• TR-RN: Reverse polarity is used for TX, Normal
polarity for RX�
• Both R: Reverse polarity is used for both TX and
RX�
Digital Code (Default: 00)
[MENU] > SET > DUP/TONE��� > Digital Code
Selects the digital code for Digital Code Squelch�
You can select a total of 100 codes (00 ~ 99)�
NOTE: The default settings shown below are for the USA transceiver version� The default settings may differ,
depending on your transceiver version�
DUP/TONE...
To Next Page
Loading...
