ITech IT8200 Series

To Next Page

To Previous Page

SWEep Subsystem

Syntax:

SWEep:WAVeform:PARameter <NRf+>

Arguments

<NRf+>

Query syntax:

SWEep:WAVeform:PARameter?

Returns:

<NRf+>

Example

SWEep:WAVeform:PAR 1.414

SWEep:PSHift <NRf+>

This command is used to set the phase shift between voltage and current.

Syntax:

SWEep:PSHift <NRf+>

Arguments

TIMe|TRIG

*RST

TIMe

Query syntax:

SWEep:PSHift?

Returns:

TIMe|TRIG

Example

SWEep:MODe TIMe

SWEep:TERMinate <mode>

This command is used to set and query the end status of sweep.

<type>: sweep wave type NORMal|LAST|OFF

Syntax:

SWEep:TERMinate <mode>

Main Page

default chapter3
- Limitation of Warranty3
- Safety Symbols3
- Warranty3
- Environmental Conditions4
- Regulatory Markings5
- Compliance Information6
- Table of Contents7
Chapter1 SCPI Introduction13
- 1.1 Overview13
- 1.4 Response Data Type16
- 1.5 Command Format17
- 1.6 Data Type19
- 1.7 Remote Interface Connection20
- Command Type of SCPI21
Chapter2 SCPI Status Register22
- Message Type of SCPI23
Chapter3 System Commands24
- System:preset24
- System:posetup <CPD25
- System:clear25
Chapter4 Channel Subsystem35
Chapter5 Abort Subsystem36
- Abort:acquire36
- Abort:list36
- Abort:sweep36
- Abort:surgesag36
Chapter6 Initiate Subsystem37
- Initiate[:Immediate]:Acquire37
- Initiate[:Immediate]:List37
- Initiate[:Immediate]:Sweep37
- Initiate[:Immediate]:Surgesag37
Chapter7 Configurate IO Subsystem38
- [Configurable:]Io:select <NR138
- [Configurable:]Io:reverse <NR1>,<CPD38
- [Configurable:]Io:type <NR1>,<CPD39
- [Configurable:]Io:tout:source <CPD1>,<CPD239
- [Configurable:]Io:state <NR1>,<CPD40
Chapter8 Trigger Subsystem41
- Trigger:list:source <Source41
- Trigger:sweep:source <CPD41
- Trigger:surgesag:source <CPD42
- Trigger:scope:source <CPD42
- Trigger:scope:mode <CPD42
- Trigger:scope:slope <CPD143
- Trigger:force43
Chapter9 Parallel Subsystem44
- Parallel:role <Role44
- Parallel:number <Number44
- Parallel:node:number45
Chapter10 Scope Subsystem46
- Scope:auto46
- Scope:run46
- Scope:single46
- Scope:stop46
- Scope:timebase:scale <Nrf46
- Scope:voltage:scale <Nrf47
- Scope:current:scale <Nrf47
- Scope:timebase:delay <Nrf48
- Scope:trigger:source48
- Scope:trigger:level <Nrf49
- Scope:trigger:slope <CPD49
- Scope:trigger:mode <CPD49
- Scope:line:selection50
- Scope:status50
- Scope:rstate50
- Scope:waveform:data51
- Scope:range:catalog51
- Scope:record:length <0.6|6|60|60051
- Scope:sample:mode <Normal|Peak52
- Scope:data:tag52
Chapter11 Fetch & Measure Subsystem53
- Fetch[:Scalar]:Current[:Ac]53
- Measure[:Scalar]:Current[:Ac]53
- Fetch[:Scalar]:Current:DC53
- Measure[:Scalar]:Current:DC53
- Fetch[:Scalar]:Current[:Ac][:Amplitude]:Maximum:positive54
- Measure[:Scalar]:Current[:Ac][:Amplitude]:Maximum:positive54
- Fetch[:Scalar]:Current[:Ac][:Amplitude]:Maximum:negative54
- Measure[:Scalar]:Current[:Ac][:Amplitude]:Maximum:negative54
- Fetch[:Scalar]:Current[:Ac][:Amplitude]:Maximum55
- Measure[:Scalar]:Current[:Ac][:Amplitude]:Maximum55
- Fetch[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:hold55
- Measure[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:hold55
- Fetch[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:hold:clear56
- Measure[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:hold:clear56
- Fetch[:Scalar]:Current:cfactor56
- Measure[:Scalar]:Current:cfactor56
- Fetch[:Scalar]:Frequency57
- Measure[:Scalar]:Frequency57
- Fetch[:Scalar]:Power[:Real]57
- Measure[:Scalar]:Power[:Real]57
- Fetch[:Scalar]:Power:apparent58
- Measure[:Scalar]:Power:apparent58
- Fetch[:Scalar]:Power:reactive58
- Measure[:Scalar]:Power:reactive58
- Fetch[:Scalar]:Power:pfactor59
- Measure[:Scalar]:Power:pfactor59
- Fetch[:Scalar]:Voltage[:Ac]59
- Measure[:Scalar]:Voltage[:Ac]59
- Fetch[:Scalar]:Voltage:DC60
- Measure[:Scalar]:Voltage:DC60
- Fetch[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum60
- Measure[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum60
- Fetch[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:positive61
- Measure[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:positive61
- Fetch[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:negative61
- Measure[:Scalar]:Voltage[:Ac][:Amplitude]:Maximum:negative61
- Fetch[:Scalar]61
- Measure[:Scalar]61
- Fetch[:Scalar]:Power[:Real]:Total62
- Measure[:Scalar]:Power[:Real]:Total62
- Fetch[:Scalar]:Power:apparent:total63
- Measure[:Scalar]:Power:apparent:total63
- Fetch[:Scalar]:Power:reactive:total63
- Measure[:Scalar]:Power:reactive:total63
- Fetch[:Scalar]:Ltlvoltage[:Ac]63
- Measure[:Scalar]:Ltlvoltage[:Ac]63
- Fetch[:Scalar]:Voltage:harmonic[:Amplitude]? <[A|B|C]>,<NR164
- Measure[:Scalar]:Voltage:harmonic[:Amplitude]? <[A|B|C]>,<NR164
- Fetch[:Scalar]:Current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR164
- Measure[:Scalar]:Current:harmonic[:Amplitude]? <[A|B|C|CH1|CH2|CH3]>,<NR164
- Fetch[:Scalar]:Voltage:harmonic:distort? <[A|B|C]>,<NR165
- Measure[:Scalar]:Voltage:harmonic:distort? <[A|B|C]>,<NR165
- Fetch[:Scalar]:Current:harmonic:distort? <[A|B|C]>,<NR166
- Measure[:Scalar]:Current:harmonic:distort? <[A|B|C]>,<NR166
- Fetch[:Scalar]:Voltage:harmonic:phase? <[A|B|C]>,<NR166
- Measure[:Scalar]:Voltage:harmonic:phase? <[A|B|C]>,<NR166
- Fetch[:Scalar]:Current:harmonic:phase? <[A|B|C]>,<NR167
- Measure[:Scalar]:Current:harmonic:phase? <[A|B|C]>,<NR167
- Fetch[:Scalar]:Voltage:harmonic:thd? <[A|B|C]67
- Measure[:Scalar]:Voltage:harmonic:thd? <[A|B|C]67
- Fetch[:Scalar]:Current:harmonic:thd? <[A|B|C]68
- Measure[:Scalar]:Current:harmonic:thd? <[A|B|C]68
- Fetch[:Scalar]:Array:voltage:harmonic[:Amplitude]? <[A|B|C]>,<NR168
- Measure[:Scalar]:Array:voltage:harmonic[:Amplitude]? <[A|B|C]>,<NR168
- Fetch[:Scalar]:Array:current:harmonic[:Amplitude]? <[A|B|C]>,<NR169
- Measure[:Scalar]:Array:current:harmonic[:Amplitude]? <[A|B|C]>,<NR169
- Fetch[:Scalar]:Array:voltage:harmonic:phase? <[A|B|C]>,<NR169
- Measure[:Scalar]:Array:voltage:harmonic:phase? <[A|B|C]>,<NR169
- Fetch[:Scalar]:Array:current:harmonic:phase? <[A|B|C]>,<NR170
- Measure[:Scalar]:Array:current:harmonic:phase? <[A|B|C]>,<NR170
- Fetch[:Scalar]:Array:voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR170
- Measure[:Scalar]:Array:voltage:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR170
- Fetch[:Scalar]:Array:current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR171
- Measure[:Scalar]:Array:current:harmonic:distort? <[A|B|C|CH1|CH2|CH3]>,<NR171
- Vetcor:oeder <NR171
- Vetcor:data72
- Vetcor:type <CPD72
Chapter12 SENSE Subsystem73
- Sense[:Remote][:State] <CPD73
- Sense:filter[:State] <CPD73
- Sense:filter:level <CPD74
- Sense:external:sync[:State] <Boolean74
- Sense:external:sync:phase <Nrf74
- Sense:external:sync:difference <Cpd>,<Nrf75
Chapter13 Load Protect Subsystem76
- [Source:]Current:protection:state <Boolean76
- [Source:]Current:protection[:Level] <Nrf76
- [Source:]Current:protection:delay <Nrf77
- [Source:]Current:peak:protection[:Level] <Nrf78
- [Source:]Current:peak:protection:delay <Nrf78
- [Source:]Power:protection:state <Boolean79
- [Source:]Power:protection[:Level] <Nrf79
- [Source:]Power:protection:delay <Nrf79
- [Source:]Voltage:under:protection:state <Boolean80
- [Source:]Voltage:under:protection[:Level] <Nrf80
- [Source:]Voltage:under:protection:delay <Nrf81
- [Source:]Voltage:peak:protection[:Level] <Nrf81
Chapter14 Source Subsystem82
- [Source:]Function <CPD182
- [Source:]Function:catalog83
- [Source:]Upfactor[:State] <Boolean83
- [Source:]Current[:Level][:Immediate][:Amplitude][:Ac] <Nrf+>[,Nrf+][,Nrf+]83
- [Source:]Current[:Level][:Immediate][:Amplitude]:DC <Nrf+>,[Nrf+],[Nrf+]84
- [Source:]Current:slew[:Ac] <Nrf+>[,Nrf+][,Nrf+]84
- [Source:]Current:slew:DC <Nrf85
- [Source:]Resistance[:Level][:Immediate][:Amplitude] <Nrf+>[,Nrf+][,Nrf+]85
- [Source:]Power[:Level][:Immediate][:Amplitude] <Nrf+>[,Nrf+][,Nrf+]85
- [Source:]Kva[:Level][:Immediate][:Amplitude] <Nrf+>[,Nrf+][,Nrf+]86
- [Source:]Pshift[:Level][:Immediate][:Amplitude] <Nrf+>[,Nrf+][,Nrf+]86
- [Source:]Cfactor[:Level][:Immediate][:Amplitude] <Nrf+>[,Nrf+][,Nrf+]87
- [Source:]Voltage[:Level][:Immediate][:Amplitude] <Nrf87
- [Source:]Ce:peak:current <Nrf+>[,Nrf+][,Nrf+]88
- [Source:]Ce:type <CPD88
- [Source:]Ce:ta:r <Nrf+>[,Nrf+][,Nrf+]88
- [Source:]Ce:ta:rl <Nrf+>[,Nrf+][,Nrf+]89
- [Source:]Ce:ta:l <Nrf+>[,Nrf+][,Nrf+]89
- [Source:]Ce:ta:rc <Nrf+>[,Nrf+][,Nrf+]89
- [Source:]Ce:ta:C <Nrf+>[,Nrf+][,Nrf+]90
- [Source:]Ce:ta:l:ainitial <Nrf+>[,Nrf+][,Nrf+]90
- [Source:]Ce:tb:r <Nrf+>[,Nrf+][,Nrf+]90
- [Source:]Ce:tb:rs <Nrf+>[,Nrf+][,Nrf+]91
- [Source:]Ce:tb:l <Nrf+>[,Nrf+][,Nrf+]91
- [Source:]Ce:tb:C <Nrf+>[,Nrf+][,Nrf+]91
- [Source:]Ce:tb:C:vinitial <Nrf+>[,Nrf+][,Nrf+]92
- [Source:]Ce:tb:D:voltage <Nrf+>[,Nrf+][,Nrf+]92
Chapter15 Input Subsystem93
- Input:coupling <CPD93
- Input:phase:loss <STATE93
- Input:line:connection <CPD93
- Input <State94
- Input:rectified[:State] <Boolean94
- Input:integrity <CPD95
- Input:protection:clear95
- Input:protection:wdog[:State] <State95
- Input:protection:wdog:delay <Time96
- Input:regulation:speed <CPD96
- Input:off:mode <CPD96
- Input:on:phase:mode <CPD97
- Input:on:phase:level <Nrf97
- Input:off:phase:mode <CPD98
- Input:off:phase:level <Nrf98
- Input:balance[:State] <Boolean99
Chapter16 ARB Subsystem101
- List:state101
- List:repeat <NR1101
- List:terminate <CPD101
- List:rstate102
- List:recall <String102
- List:step:count103
- List:clear103
- LIST:STEP <Nr1>,<String103
- LIST:STEP:ITEM <Nr1>,<Nr1>,<Nrf105
- LIST:STEP:ITEM? <Nr1>,<Item106
- List:name107
- List:save <Filename107
- List:configure107
- List:create107
- List:file:number107
- LIST:FILE:NAME? <Index108
- List:file:delete <Filename108
- List:step:jump <Nr1108
- List:function <CPD109
- List:DCCV:state <Boolean109
- List:DCCV:voltage <Nrf109
Chapter17 Surgesag Subsystem111
- Surgesag:mode <Mode111
- Surgesag:phase:start <Nrf111
- Surgesag:phase:width <Nrf112
- Surgesag:action <Action112
- Surgesag:symmetry <Bool113
- Surgesag:repeat:count <NR1113
- Surgesag:period:count <NR1114
- Surgesag:value:select <Mode115
- Surgesag:value:percent <Nrf115
- Surgesag:value:setting <Nrf116
- Surgesag:chan:enable <A|B|C|AB|AC|BC|ABC116
- Surgesag:save <String117
- Surgesag:recall <String117
- Surgesag:state117
Chapter18 Waveform Subsystem118
- Waveform[:Immediate] <Waveform>,[Waveform],[Waveform]118
- Pwaveform[:Immediate] <Phase/Chan>,<Waveform119
- Waveform:edit:parameter <Phase/Chan>,<Percent1119
- Waveform:edit:thd:clear120
- Waveform:edit:thd:import <Filename120
- Waveform:edit:thd:formula <Formula121
- Waveform:edit:thd:data <Order>,<String121
- Waveform:edit:thd:save:local <Filename121
- Waveform:edit:thd:save:udisk <Filename122
- Waveform:edit:userdefine:clear122
- Waveform:edit:userdefine:import <Filename122
- Waveform:edit:userdefine:mode <Symmtery123
- Waveform:edit:userdefine:data <Index>,<Normalization123
- Waveform:edit:userdefine:save:local <Filename124
- Waveform:edit:userdefine:save:udisk <Filename124
Chapter19 Sweep Subsystem125
- Sweep:function <Mode125
- Sweep:level:start <Nrf+>[,<Nrf+>,<Nrf+>]125
- Sweep:level:stop <Nrf+>[,<Nrf+>,<Nrf+>]126
- Sweep:level:step <Nrf+>[,<Nrf+>,<Nrf+>]126
- Sweep:time:step <Nrf127
- Sweep:mode <Mode127
- Sweep:waveform <Name128
- Sweep:waveform:parameter <Nrf128
- Sweep:pshift <Nrf129
- Sweep:terminate <Mode129
- Sweep:trig:source <Mode130
- Sweep:step:repeat <NR1130
Chapter20 IEEE-488 Common Commands132
- Cls132
- Ese132
- Ese133
- Esr133
- Idn133
- Opc134
- Rst134
- Sre <Nr1134
- Stb135
- Psc135
- Sav136
- Rcl136

Table of Contents

Other manuals for ITech IT8200 Series