126
3 If “Load ****** .SNG too” is checked, you can use “Select
.SNG Allocation” to specify how multi data within the
.SNG file will be loaded.
Append: The multi data will be loaded starting at the
number that follows the last multi data in memory. The
multi data within the .SNG file that is being loaded will
be packed into the available locations (
☞“.SNG Alloca-
tion” diagram in “Load .SNG too”). Select this method
when you wish to load multi data from disk without
erasing the multi data that is already in memory.
Clear: All multi data existing in memory will be erased,
and the multi data of the file will be loaded with the
same configuration in which it was saved (
☞“.SNG Allo-
cation” diagram in “Load .SNG too”). Select this method
when you wish to reproduce the exact state that was
saved, such as immediately after the power is turned on.
4 If “Load ****** .SNG too” is checked, you can use “Load
track events?” to specify how track events within the
.SNG file will be loaded.
On (Checked): Track events and user pattern events in
the .SNG file will be loaded.
Off (Unchecked): Only user pattern events will be
loaded; track events will not be loaded.
Normally you will leave this Off.
Track events are recorded in .SNG files saved by the
TRITON/TRITONpro/TRITONproX, but cannot be
used by the Multi mode of the TRITON-Rack even if
they are loaded.
However, track events loaded into Multi mode can be
converted into demo song data using the DEMO/SNG
Utility “Make Demo Data.” If you wish to do so, “Load
track events?” checked to load the track events.
For the procedure of creating demo song data, refer to
p.139 “Make Demo Song.”
If the .SNG file does not contain any events to load,
only the Multi track settings will be loaded.
5 “.KSC Allocation” is valid if “Load
********
.KSC too” has
been checked. You can specify how the multisamples
and samples in the .KSC file will be loaded.
Append: Samples will be loaded starting at the first
unoccupied number following the last multisample or
sample that currently exists in memory (i.e., by having
been sampled or loaded). At this time, only the valid
multisamples or samples will be loaded, and they will be
organized in numerical order. (
☞“.SNG Allocation” dia-
gram)
At the same time, programs within the .PCG file that use
multisamples from the .KSC file will automatically have
the multisample settings for their oscillators rewritten so
that each program uses the correct multisample. Drum
kits in the .PCG file that use samples from the .KSC file
will automatically have the sample settings for the drum
kit rewritten so that the drum kit uses the correct sam-
ples.
Clear: All multisamples and samples currently in mem-
ory will be erased, and the multisamples and samples
will be loaded in the same configuration in which they
were saved. (
☞“.SNG Allocation” diagram)
If memory already contains multisamples or samples
that you wish to keep, and you wish to load additional
multisamples or samples from disk, select Append.
If the power has just been turned on, or you want to
reproduce the state that was saved, select Clear.
6 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
2) Load Programs: selected icon
All program data from a .PCG file will be loaded.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
3) Load Program Bank [I–A...I–E, E–A...E–H]:
selected icon
All program data of the selected bank will be loaded into the
bank you specify.
1 In “To,” select the loading destination bank.
Bank I–F program data can be loaded only into bank I–
F. If you select bank I–A...I–E, E–A...E–H, it will not be
possible to select bank I–F in “To.”
2 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
4) Load a Program: selected icon
Data for the selected program will be loaded into the pro-
gram number you specify.
1 If you wish to load a program other than the one already
selected, use “From” to select the program that you wish
to load.
2 In “To,” select the bank and program into which the data
will be loaded.
Data for one bank I–F program can be loaded only into
bank I–F. If bank I–A – I–E or E–A – E–H is selected in
“From,” bank I–F cannot be selected in “To.”
3 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
.SNG Allocation
SNG000
SNG001
SNG005
SNG003
.SNG file to load
SNG000
SNG002
SNG003
Internal memory of
the TRITON-Rack
before loading
SNG000
SNG002
SNG005
SNG003
Internal memory of the
TRITON-Rack after loading
SNG000
SNG001
SNG005
SNG003
SNG004
SNG007
SNG006
SNG000
SNG001
SNG005
SNG003
SNG000
SNG002
SNG003
Append
Clear
To Next Page
Loading...
