LS Industrial Systems SV-iV5 Series - 5.4 Function Group (FUN_[][])

5. Function Code Table
5-5
LsigmaÆ If/Tr/Ls Tune.
3) Caution: PAR_33 (Enc Scale) Code is necessary only in the case of installation of SIN/COS Encoder option board, Don’t modify the
default value “X1” when not using SIN/COS Encoder board. If you modify the value, the normal operation isn’t possible. For any extra
information in detail, refer to the option dedicated manual.
5.4. Function group (FUN_[][])
SETTING DATA
CODE
NO.
Comm.
Addr
CODE NAME LCD DISPLAY
RANGE UNIT DEFAULT
Adjustment
During Run
PAGE
FUN_00 - Jump for quick view Jump code 1 ~ 69 - - Yes
FUN_01 7401
RUN/STOP command
source selection
Run/Stop Src
0 (Terminal 1)
1 (Terminal 2)
2 (Keypad)
3 (Option)
- 0 (Terminal 1) No
6-36
FUN_02 7402
Speed setting source
selection
Spd Ref Sel
0 (Analog)
1 (Keypad1)
2 (Keypad2)
3 (Option)
6 (Line SPD Ref)
1)
7 (Line SPD Opt)
1)
- 1 (Keypad1) No
FUN_03 7403 Stop mode selection Stop mode
0 (Decel)
1 (Free-run)
- 0 (Decel) No
FUN_04 7404 Max. motor speed Max Speed 400.0 ~ 3600.0 rpm 1800.0 No
6-37
FUN_12 740C Multi-step speed 0 Speed 0 0.0~Max Speed rpm 0.0 Yes
FUN_13 740D Multi-step speed 1 Speed 1 0.0~Max Speed rpm 0.0 Yes
FUN_14 740E Multi-step speed 2 Speed 2 0.0~Max Speed rpm 0.0 Yes
FUN_15 740F Multi-step speed 3 Speed 3 0.0~Max Speed rpm 0.0 Yes
FUN_16 7410 Multi-step speed 4 Speed 4 0.0~Max Speed rpm 0.0 Yes
FUN_17 7411 Multi-step speed 5 Speed 5 0.0~Max Speed rpm 0.0 Yes
FUN_18 7412 Multi-step speed 6 Speed 6 0.0~Max Speed rpm 0.0 Yes
FUN_19 7413 Multi-step speed 7 Speed 7 0.0~Max Speed rpm 0.0 Yes
FUN_20 7414 JOG speed Jog Speed 0.0~Max Speed rpm 100.0 Yes
FUN_21 7415 Dwell Speed Dwell Speed 0.0~Max Speed rpm 100.0 No
6-37
FUN_22 7416 Dwell Time Dwell Time 0.00 ~ 100.00 sec 0.00 No 6-38
FUN_33 7421
Acc./Dec. reference
Speed
Acc/Dec Ref
0 (Max Speed)
1 (Ref Speed)
-
0
(Max Speed)
No 6-39
FUN_36 7424
S ratio 1 in acceleration
start
Acc S Start 0.0 ~ 50.0 % 0.0 No
FUN_37 7425
S ratio 2 in acceleration
start
Acc S End 0.0 ~ 50.0 % 0.0 No
FUN_38 7426
S ratio 1 in deceleration
start
Dec S Start 0.0 ~ 50.0 % 0.0 No
FUN_39 7427
S ratio 2 in deceleration
start
Dec S End 0.0 ~ 50.0 % 0.0 No
6-40
FUN_40 7428 Acceleration time 1 Acc Time-1 0.00 ~ 6000.0 sec 2.00 Yes
FUN_41 7429 Deceleration time 1 Dec Time-1 0.00 ~ 6000.0 sec 2.00 Yes
FUN_42 742A Acceleration time 2 Acc Time-2 0.00 ~ 6000.0 sec 3.00 Yes
FUN_43 742B Deceleration time 2 Dec Time-2 0.00 ~ 6000.0 sec 3.00 Yes
FUN_44 742C Acceleration time 3 Acc Time-3 0.00 ~ 6000.0 sec 4.00 Yes
FUN_45 742D Deceleration time 3 Dec Time-3 0.00 ~ 6000.0 sec 4.00 Yes
FUN_46 742E Acceleration time 4 Acc Time-4 0.00 ~ 6000.0 sec 5.00 Yes
FUN_47 742F Deceleration time 4 Dec Time-4 0.00 ~ 6000.0 sec 5.00 Yes
6-39
FUN_48 7430
Deceleration time
selection for zero speed
Use 0 Dec T
0 (No)
1 (Yes)
0 (No) Yes
FUN_49 7431
Deceleration time for zero
speed
0 Dec Time 0.00 ~ 6000.0 sec 0.00 Yes
6-42
FUN_51 7433
Deceleration time
for emergency stop
BX Time 0.0 ~ 6000.0 sec 0.0 Yes
FUN_52 7434 Pre-excitation time PreExct Time 0 ~ 10000 ms 0 No
FUN_53 7435 Hold Time Hold Time 100 ~ 10000 ms 1000 No
6-43
FUN_54 7436
Electronic thermal
selection
ETH Select
0 (No)
1 (Yes)
- 0 (No) Yes 6-44
1) Displayed when setting WEB Control Mode.