Minebea CC-Link CSD-892-73 - Page 156

145
Specications & Others
External control input (Confirmation) 2-5, 6-6, 6-9, 7-2,
8-6, 8-8-1, 13-1, 13-4,
16-3, 17-2, 18-3
External control output (Confirmation) 1-1, 2-5, 7-2,
8-8-2, 9, 13-5, 11, 13-1,
16-3, 17-2, 18-3
External control output (Confirmation) Change logic
7-2, 8-8-3
EzCTS mode (EzCTS_USB1)..... 1-1, 3-1, 3-2, 13-2
【E】
F.G.(FG) ...................................... 2-4, 2-6
F/ENTER key (Operation) ........... 1-1
, 7-2, 8-4, 8-7, 16-3
Final / Preliminary 1/2 ................. 11-2-2, 11-2-3, 11-2-4,
12-2, 14-5-1, 16-3
Fine adjustment of ZERO/SPAN . 4-7
Free fall ....................................... 11-2-2, 11-2-3, 11-2-4,
12-2, 14-5-1,16-3
Front panel .................................. 1-1, 1-2, 8-4
FULL ........................................... 7-2, 8-8-2, 11-2, 11-2-2,
11-2-3, 11-3-2, 12-2,
14-5-1, 14-5-2
, 16-3,
18-3
FULL comparative operation ....... 3-1, 9-2, 10-5, 11-2-2,
11-2-3, 11-3-2
Full flow ....................................... 7-2, 8-8-2, 11-2-2,
11-2-3, 11-2-4
FUNC. key ................................... 1-1, 8-4
Function clear.............................. 3-1, 7-2, 8-11
Function mode ............................ 3, 7, 8
【G】
Gross........................................... 1-1, 18-2
Gross displ
ay .............................. 6-9, 6-9-1, 7-2, 8-8-1,
8-8-2, 14-5-2,16-3, 18-3
【H】
HOLD .......................................... 1-1, 3-1, 7-2, 8-6, 8-7,
8-8-1, 8-8-2, 14-5-2,
16-3, 18-2, 18-3, 19
HOLD Target ............................... 7-2, 8-6-1
【I】
IN1 ~ 5 (INPUT) .......................... 2-5, 13-4
Input noise................................... 18-1
Input range ..............................
.... 18-1
Input sensitivity............................ 18-1
Internal RAM ............................... 5-2, 6-10, 12, 16-3
【J】
Judgement display ...................... 18-2
Junction box for extension .......... 2-3
【K】
Key lock....................................... 1-1, 3-1, 7-2, 8-4, 8-8,
16-3, 17-1
【L】
Level input ................................... 2-5, 8-8-1, 17-2, 18-3
Load cell parallel connection .....
.. 2-3, 18-1
Load display section.................... 1-1, 18-2
LOCK .......................................... 1-1, 18-2
Lower terminal block ................... For safe operation-5,
1-2, 2-5, 13-4, 13-5, 11
【M】
Maintenance date / number ........ 7-2, 8-9
Mass of weight ............................ 4, 5-2, 14-6-6, 16-5
Measurement mode .................... 3-1, 6-11, 8-8, 9, 9-2,
10-1, 11, 16-3, 17-2
mini US
B connector B-type ......... 1-1, 13-2, 18-3
Monitor mode .............................. 13-6, 17-1
mV/V ........................................... 1-1, 18-2
【N】
Near ZERO ................................. 7-2, 8-8-2, 11-2-2,
11-2-3, 11-3-2, 12-2,
14-5-1, 14-5-2, 16-3,
18-3
Near ZERO Comparative operation 3-1, 9-2, 10-4,
11-2-2, 11-2-3, 11-3-2
NET ............................................. 1-1, 18-2
Net value ..................................... 7-2, 8-8-2, 11-2-3, 11-2-4
14-5-2, 16-3, 18-3
Non-linearity ................................ 18-1
【O】
ON time of liquid crystal backlight 7-2, 8-10, 16-3, 17-1
Open collector ............................. 2-5, 13-5, 17-2
Operation mode .......................... 14-5-1, 14-5-2, 16-2,
16-2-1, 16-3
Operation of comparative signal . 3-1, 9-1, 9-2, 10-3, 16-3
OUT1 ～
5 (OUTPUT) ................ 2-5, 13-5, 18-2
Outline dimension ....................... For safe operation-2,
18-4
OVER .......................................... 7-2, 8-8-2, 11-2-2,
11-2-3, 11-2-4, 12-2,
14-5-1, 14-5-2, 16-3,
18-3
Overload (Display) ...................... 1-1, 3-1, 5-2, 6-3, 16-3
16-4, 16-5, 17-1, 18-2,
19
【P】
Parity (Bit) ................................... 7-2, 16-1, 16-2-3, 16-3
PLC
(Memory) ............................. 2-6, 11, 11-2, 14-4, 16-2
Power consumption..................... 18-4
Power on ZERO .......................... 3-1, 5-2, 6-8, 16-3, 19
Power supply +/- and input +/- for load cell 2-3
Pressure sensor .......................... 2-3
Pulse input .................................. 2-5, 8-8-1, 17-2, 18-3
【R】
RD ............................................... 1-1, 18-3
Remote I/
O .................................. 14-2, 14-5-2