Motion Control Engineering Nidec Element Series

Index-12 Manual # 42-02-2P26
Parameter Update message 2-84
PLD DSL1 Mismatch message 2-85
PLD DSL2 Mismatch message 2-85
PLD DTL Mismatch message 2-85
PLD MRDN Mismatch message 2-85
PLD MRIN Mismatch message 2-85
PLD MRUP Mismatch message 2-85
PLD USL1 Mismatch message 2-85
PLD USL2 Mismatch message 2-85
PLD UTL Mismatch message 2-85
SPA Comm Sync message 2-85
SPA is Offline message 2-85
SPC Comm Sync message 2-85
SPC is Offline message 2-86
UETS Position High message 2-86
UETS Position Low message 2-86
UETS Speed High message 2-86
SPB Flags 2-16
SPB Inputs 2-16
SPB Numeric 2-16
SPB Outputs 2-16
SPB Powerup/Reset message 2-84
SPC 2-27
3HN Comm Loss message 2-86
CAN 3 Comm Loss message 2-86
CAN Comm Loss message 2-86
SPA is Offline message 2-86, 2-87
SPB is Offline 2-87
SPC Flags 2-16
SPC Inputs 2-16
SPC Numeric 2-16
SPC Outputs 2-16
SPC Started Up message 2-86
SPD(n) 2-27
Speed and Acceleration Control 1-49
Speed Changes Felt Excessively in Car 1-60
Speed display 1-13
Speed Drop Delay 2-14
Speed Pick Delay 2-14
speed pick delay 1-51
Standard Acceleration 2-11
Standard Deceleration 2-11
Standard enclosure 1-3
Standard Roll Jerk 2-11
Standard Start Jerk 2-11
Standard Stop Jerk 2-11
Start Jerk 2-11
Status Info 2-33
Status Information 1-13
status information 2-5
status of dedicated inputs 2-16
status of dedicated outputs 2-16
status of door control inputs/outputs 2-16
status of landing system inputs/outputs 2-16
status of programmable inputs 2-16
status of programmable outputs 2-16
STD 2-20, 2-27
Steel tape 1-28
Stick alignment 1-31
Stop Jerk 2-11
Stopping Accuracy 3-2
STU 2-20, 2-27
Stuck Car Call message 2-87
Stuck Door Open Button message 2-87
Stuck Door Zone Fault message 2-87
Stuck Down Hall Call message 2-87
Stuck Insp Input 2-7
Stuck Leveling Fault message 2-87
Stuck PHE Timer 2-8
Stuck Photo Eye message 2-87
Stuck Safe Edge message 2-88
Stuck Sensor (Edge) message 2-88
Stuck Up Hall Call message 2-88
Subnet Mask 2-15
Supported Door Operators 1-2
Suspension Integrity message 2-88
Suspension Means Integrity fault 2-88
SW5 2-43
System Control Parameters 2-13, 2-14
System Inputs 2-16, 2-32
System Outputs 2-16, 2-32
System Timers 2-8
T
Tape cleaning 1-28
Tape Tension 1-30
TAPS 1-9
TAPS Testing 3-10
Temperature 1-5
Terminal Switch Configuration 1-27
Terminal Switch Learn 1-10, 1-57, 2-15
Terminal Switch Learn message 2-88
Terminal Sync (Edge) message 2-88
terminate the CAN 2-36
TEST 2-27
Test 1-5
Test Hall Calls 2-33
Test hall calls 1-45
Test Mode 1-9
Test mode 2-41
Test Mode message 2-88
Test speed 1-64
Test Type 1-64
TEST/PRETEST 2-41
Test/Pretest 1-19, 2-41
Thermal overload 2-45
Top Access Distance 2-9
Top Access, DOWN 2-45
Top Access, UP 2-45
Top Deviation (Edge) message 2-88
Top Floor 2-5
Touch screen locks up 2-2
touchscreen 2-2
TP1 2-49
TP2LS 2-49
TPEB3 2-49
TPEB34 2-49
TPEB4 2-49
TPMSAF 2-49
TR_HY 2-46, 2-56