To Next Page
J
Jeffrey HoodSep 18, 2025
What to do if received bad response from BMC on NEC Express5800?
- MMark KingSep 22, 2025
Check the server. A failure may have occurred in BMC. If you do not find any problem, contact your service representative.
What to do if received bad response from BMC on NEC Express5800?
Check the server. A failure may have occurred in BMC. If you do not find any problem, contact your service representative.
How to fix Invalid BMC configuration file on NEC Server?
The BMC configuration file may be corrupted. Check the file.
How to resolve 'BMC Memory Test Failed' error on NEC Express5800 Server?
If your NEC Server shows the error 'BMC Memory Test Failed', power off and reboot the server. If the error continues, contact your service representative.
How to fix 'BMC SDR Repository empty' error on NEC Express5800 Server?
If your NEC Server shows the error 'BMC SDR Repository empty', power off and reboot the server. If the error persists, contact your service representative.
What to do with Windows 2000 installation warning on NEC Express5800?
If a warning is registered in the System Log of the Event Viewer during Windows 2000 installation on your NEC Server, no action is required as there is no problem associated with this issue.
How to fix Writing has failed error on NEC Express5800?
Try again. If the error persists, contact your service representative because a failure may have occurred in BMC.
How to resolve failed to write the file error on NEC Express5800?
The BMC configuration file is not saved successfully. Change the location to save the file and try again.
How to resolve invalid file size error on NEC Express5800 Server?
The update file may be corrupted. Obtain the update file again.
What is considered Invalid host name for NEC Server?
You can use only alphanumeric characters, minus sign (–), and underscore (_) for a host name. A host name should be 64 characters or less.
How to fix NEC Express5800 not found on the network?
If the NEC Server is not found on the network, the internal LAN controller may be disabled in the BIOS SETUP utility. Check the LAN controller setting using the BIOS SETUP utility to resolve this issue.
General| Series | Express5800 |
|---|---|
| Category | Server |
| Processor | Intel Xeon processors |
| Network | Gigabit Ethernet, 10 Gigabit Ethernet (Varies by model) |
| Operating System Support | Windows Server, Linux variants |
| Form Factor | Tower, Rackmount (1U, 2U, etc. - varies by model) |
| Memory | DDR4 ECC DIMM (Capacity varies by model) |
| Storage | SAS/SATA HDD/SSD, NVMe SSD (Configuration varies by model) |
Details on warning labels placed on system components to alert users about potential hazards.
Provides essential precautions for safe server operation, emphasizing general safety measures and potential risks.
Covers safe practices for using power supplies and cords, including warnings about wet hands and proper outlet usage.
Outlines critical safety procedures for handling internal components, including warnings about lasers and lithium batteries.
Details crucial do's and don'ts during server operation to prevent hazards and ensure system integrity.
Provides essential instructions for successful server operation, covering installation, power, and environmental conditions.
Covers fundamental server operations such as powering on/off and using the security lock for door access.
Details the steps to power on the server, including checking peripherals and the POST process.
Explains the correct procedure for safely powering off the server and all connected peripheral devices.
Explains RAID configuration requirements for built-in disks and how to pair disks for mirroring.
Guides on how to locate failed hard disks using ESMPRO Manager and the procedure for replacement.
Details the manual procedure for restoring redundant disk configurations after failures or changes.
Introduces the BIOS SETUP utility for basic hardware configuration and management of server settings.
Describes how to start the BIOS SETUP utility and enter the main menu, including password entry.
Details how to set Supervisor and User passwords, and enable/disable the POWER switch for security.
Explains how to change the boot device order for starting the system and NEC EXPRESSBUILDER.
Guides on using the SCSISelect utility for configuring SCSI controller settings and device transfer speeds.
Details procedures for forced shutdown and clearing CMOS data or passwords using jumper pins.
Step-by-step guide on how to clear BIOS passwords by manipulating jumper switches on CPU/IO modules.
Introduces the ft Remote Management Card and its capabilities for remote server monitoring and control.
Guides on performing initial settings for the remote management card, including BMC configuration.
Explains how to connect to the server for remote management via a web browser and default network values.
Details how to configure BMC network settings, including IP addresses for LAN ports.
Explains how to use the remote KVM console for video, keyboard, and mouse control of the server.
Details how to launch the remote KVM console window from the control panel for server interaction.
Guides on configuring BMC settings, including reading, saving, and editing configuration files.
Covers network settings for BMC, including IP address and port configurations for remote management.
Details web server settings for the BMC, such as HTTP port, SSL enable/disable, and login attempts.
Provides guidelines for regular server checks and maintenance to ensure optimal condition.
Advises monitoring for failure occurrences using NEC ESMPRO and checking alerts on the management PC.
Guides on checking LED indications on the server for status and error detection.
Explains how to run system diagnostics to test server components and their connections.
Explains how errors are posted and categorized, including fatal, logon, access privilege, and network errors.
Lists common POST error messages, their causes, and recommended actions for resolution.
Provides a systematic approach to solving common server problems, starting with power and POST checks.
Provides critical safety warnings and precautions to be followed during component installation or removal.
Outlines essential anti-static measures to prevent damage to electronic components during installation.
Guides on installing 3.5-inch hard disk drives into server bays, including RAID configuration.
Details the procedure for replacing a failed hard disk drive, including locating and restoring configuration.
Highlights crucial precautions for installing ft Remote Management Cards, including power and static electricity.
