What to do if NEC Computer Hardware drive is not correctly recognized when the system is started up?
If the drive is not correctly recognized when the system starts, verify that the drive is connected in the correct position within the system configuration.
How to fix NEC Computer Hardware ambient temperature alarm 02?
To resolve a low temperature error, ensure the ambient temperature of the installation location meets the operation guarantee condition. If the error persists, contact your service representative.
How to fix NEC Computer Hardware ambient temperature alarm 09?
To address a high temperature error in the Tape Blade, check that the Blade Enclosure fans are working normally. Refer to the Blade Enclosure User’s Guide to ensure the correct number of fans are installed in the proper locations. Verify that the fans and Tape Blade are installed correctly. Also, ensure the ambient temperature of the installation location meets the operation guarantee condition. If the issue persists, contact your service representative.
Why is NEC Computer Hardware transfer speed not correct?
Because the internal LAN controller of the Tape Blade operates on a network with a transfer rate of 1Gbps, open the network property dialog box in the control panel to set the 'Link Speed' value to match the value specified for the HUB.
What to do if NEC Computer Hardware correctly backing up is not possible (and the clean LED is blinking)?
If the clean LED is blinking and backups are failing, and the problem continues after cleaning, replace the data cartridge.
Why I am unable to start EXPRESSBUILDER on my NEC Express5800 Server?
There are several reasons why you might be unable to start EXPRESSBUILDER on your NEC Server: * The EXPRESSBUILDER version may not be designed for your computer. Use the EXPRESSBUILDER provided with the server. If the error persists, you may need further assistance. * EXPRESSBUILDER could not find the hardware information on the motherboard. * A file or folder in EXPRESSBUILDER failed to read, possibly because the media is defective or the optical disk drive is faulty.
Why is NEC Computer Hardware CPU blade not found on the network?
If the CPU blade isn't found on the network, check the network cable connection and ensure it meets the network interface standard. Also, verify that the internal LAN controller isn't disabled in the CPU blade's BIOS SETUP utility.
What to do if NEC Computer Hardware cleaning cartridge cannot be ejected?
If a used cleaning cartridge is stuck or cleaning didn't finish because the cartridge was used up, press the EJECT button to remove it. Then, restart cleaning with a new cleaning cartridge.
How to fix NEC Computer Hardware location error?
To fix a location error, refer to the Blade Enclosure User's Guide to ensure the Tape Blade is in the correct location. Check the installation locations of the fan and Tape Blade. If the error persists, contact your service representative.
What to do if NEC Computer Hardware correctly backing up is not possible (and the backup software does not recognize the drive)?
If the backup software doesn't recognize the drive, verify that the backup software is correctly installed.
General| Series | Express5800 |
|---|---|
| Category | Server |
| Processor | Intel Xeon processors |
| Network | Gigabit Ethernet, 10 Gigabit Ethernet (Varies by model) |
| Operating System Support | Windows Server, Linux variants |
| Form Factor | Tower, Rackmount (1U, 2U, etc. - varies by model) |
| Memory | DDR4 ECC DIMM (Capacity varies by model) |
| Storage | SAS/SATA HDD/SSD, NVMe SSD (Configuration varies by model) |
Details on warning labels placed on system components to alert users about potential hazards.
Provides essential precautions for safe server operation, emphasizing general safety measures and potential risks.
Covers safe practices for using power supplies and cords, including warnings about wet hands and proper outlet usage.
Outlines critical safety procedures for handling internal components, including warnings about lasers and lithium batteries.
Details crucial do's and don'ts during server operation to prevent hazards and ensure system integrity.
Provides essential instructions for successful server operation, covering installation, power, and environmental conditions.
Covers fundamental server operations such as powering on/off and using the security lock for door access.
Details the steps to power on the server, including checking peripherals and the POST process.
Explains the correct procedure for safely powering off the server and all connected peripheral devices.
Explains RAID configuration requirements for built-in disks and how to pair disks for mirroring.
Guides on how to locate failed hard disks using ESMPRO Manager and the procedure for replacement.
Details the manual procedure for restoring redundant disk configurations after failures or changes.
Introduces the BIOS SETUP utility for basic hardware configuration and management of server settings.
Describes how to start the BIOS SETUP utility and enter the main menu, including password entry.
Details how to set Supervisor and User passwords, and enable/disable the POWER switch for security.
Explains how to change the boot device order for starting the system and NEC EXPRESSBUILDER.
Guides on using the SCSISelect utility for configuring SCSI controller settings and device transfer speeds.
Details procedures for forced shutdown and clearing CMOS data or passwords using jumper pins.
Step-by-step guide on how to clear BIOS passwords by manipulating jumper switches on CPU/IO modules.
Introduces the ft Remote Management Card and its capabilities for remote server monitoring and control.
Guides on performing initial settings for the remote management card, including BMC configuration.
Explains how to connect to the server for remote management via a web browser and default network values.
Details how to configure BMC network settings, including IP addresses for LAN ports.
Explains how to use the remote KVM console for video, keyboard, and mouse control of the server.
Details how to launch the remote KVM console window from the control panel for server interaction.
Guides on configuring BMC settings, including reading, saving, and editing configuration files.
Covers network settings for BMC, including IP address and port configurations for remote management.
Details web server settings for the BMC, such as HTTP port, SSL enable/disable, and login attempts.
Provides guidelines for regular server checks and maintenance to ensure optimal condition.
Advises monitoring for failure occurrences using NEC ESMPRO and checking alerts on the management PC.
Guides on checking LED indications on the server for status and error detection.
Explains how to run system diagnostics to test server components and their connections.
Explains how errors are posted and categorized, including fatal, logon, access privilege, and network errors.
Lists common POST error messages, their causes, and recommended actions for resolution.
Provides a systematic approach to solving common server problems, starting with power and POST checks.
Provides critical safety warnings and precautions to be followed during component installation or removal.
Outlines essential anti-static measures to prevent damage to electronic components during installation.
Guides on installing 3.5-inch hard disk drives into server bays, including RAID configuration.
Details the procedure for replacing a failed hard disk drive, including locating and restoring configuration.
Highlights crucial precautions for installing ft Remote Management Cards, including power and static electricity.
To Next Page
