Subject to reasonable modifications due to technical advances. © Pepperl+Fuchs, Printed in Germany
5
Pepperl+Fuchs Group · Tel.: Germany (6 21) 7 76-0 · USA (3 30) 4 25 35 55 · Singapore 7 79 90 91 Internet http://www.pepperl-fuchs.com
Issue date: 17.4.2009
AS-Interface
Table of contents
8.6 Safe coupling slaves on the AS-i circuits.................................................... 51
8.7 Chip card ........................................................................................................ 51
8.7.1 Unsafe data.................................................................................................................... 51
8.7.1.1 Card unformatted .........................................................................................................51
8.7.1.2 Data not compatible ..................................................................................................... 52
8.7.1.3 Card empty................................................................................................................... 52
8.7.1.4 Data compatible ........................................................................................................... 52
8.7.1.5 Data in the device and on the chip card identical......................................................... 52
8.7.1.6 Data in the device and on the chip card not identical................................................... 52
8.7.2 Safe data ........................................................................................................................ 53
8.7.2.1 Data incompatible ........................................................................................................53
8.7.2.2 Data compatible ........................................................................................................... 54
8.7.2.3 Complete configuration ................................................................................................ 54
8.7.2.4 Data on the chip card and in the device are identical .................................................. 54
8.7.2.5 Data not identical ......................................................................................................... 55
8.7.2.6 Operating the chip card from the menu........................................................................ 55
8.7.3 Working with multiple memory banks ........................................................................ 55
9 Operation in advanced display mode............................................... 57
9.1 Overview ......................................................................................................... 57
9.2 Navigating through the advanced display mode ........................................ 61
9.3 ETHERNET/IP (main menu) ........................................................................... 62
9.3.1 TCP/IP Object ................................................................................................................ 62
9.3.1.1 IF STATUS................................................................................................................... 62
9.3.1.2 IF CAPABILITY ............................................................................................................63
9.3.1.3 IF CONTROL ...............................................................................................................63
9.3.1.4 PATH TO LINK OBJECT ............................................................................................. 64
9.3.1.5 TCP/IP CONFIG........................................................................................................... 64
9.3.2 ETHERNET OBJECT ..................................................................................................... 65
9.4 QUICK SETUP ................................................................................................ 66
9.5 AS-I SAFETY................................................................................................... 67
9.5.1 TEACH CODES .............................................................................................................. 68
9.5.1.1 TEACH CODES – COMPLETE ................................................................................... 68
9.5.1.2 SINGLE SLAVE ........................................................................................................... 70
9.5.1.3 COUPLING SLAVE...................................................................................................... 71
9.5.1.4 INPUT CODE SEQ. ..................................................................................................... 72
9.5.2 SAFE OUTPUT CH (channels for the release circuits) .............................................. 72
9.5.3 SAFE COUPLING (optional menu)............................................................................... 73
9.5.4 START/STOP (changing the Monitor mode)............................................................... 73
9.5.5 CLEAR SAFE CFG (delete safe configuration)........................................................... 74
9.5.6 PIN (changing the PIN) ................................................................................................. 74
9.5.7 SAFE CHIPCARD........................................................................................................... 75
9.5.7.1 VIEW BANK X CONFIG (view active bank) ................................................................. 76
9.5.7.2 CARD –>MONITOR (copy card data to the Monitor) ................................................... 77
9.5.7.3 MONITOR –>CARD (copy Monitor data to the chip card) ........................................... 78
9.5.7.4 CLEAR CODES (delete code sequences) ................................................................... 80
9.5.7.5 CLEAR SAFE CARD.................................................................................................... 81
9.5.8 PROTECT (protect safe configuration) ....................................................................... 82
9.5.9 SAFETY SUBST VAL (Substitute values for input data from safe slaves) .............. 82
9.6 DIAGNOSTICS ................................................................................................ 83
9.6.1 AS-I CIRCUIT (Selecting the AS-i circuit).................................................................... 84
9.6.2 SAFETY SLAVES (safety oriented slaves).................................................................. 84
To Next Page
Loading...
Need help?
General
