Pilz PNOZ s30 - Example: Configure Basic Configuration 2

134 pages

To Next Page

To Previous Page

Display menu - Configuration

Operating Manual PNOZ s30

1001715-EN-19

| 86

8.8 Example: Configure basic configuration 2

Main Page

Table of Contents3
Introduction7
Validity of Documentation7
Using the Documentation7
Definition of Symbols7
Overview9
Unit Structure9
Range9
Unit Features9
Front/Side View10
Safety12
Intended Use12
Safety Regulations12
Safety Assessment12
Use of Qualified Personnel13
Warranty and Liability13
Disposal13
For Your Safety13
Security14
Function Description15
Introduction15
Block Diagram15
Functions16
Standstill16
Speed17
Speed Range17
Position18
Direction20
Encoder Diagnostics / Broken Shearpin Monitoring21
Hysteresis21
Frequency Filtering22
Start Types24
Start-Up Delay24
Synchronous Start25
Outputs25
Switch Delay26
Feedback Loops26
Analogue Output27
Units27
Timing Diagram for Speed Monitoring28
Speed Configuration29
Select Inputs31
Switch Functions33
Special Functions35
Basic Configuration37
Chip Card38
Input Device Types39
Proximity Switch39
Rotary Encoders40
Output Signals41
Adapter for Incremental Encoders42
Installation43
General Installation Guidelines43
Dimensions43
Wiring44
General Wiring Guidelines44
Pin Assignment of RJ45 Socket44
Supply Voltage44
Connection of Proximity Switches45
Connection of a Rotary Encoder46
Connect Rotary Encoder to Speed Monitor47
Connect Rotary Encoder with Z Index to Speed Monitor47
Connect Rotary Encoder to the Speed Monitor Via an Adapter48
Connection of Proximity Switch and Rotary Encoder48
Reset Circuit50
Feedback Circuit50
Select Inputs51
Semiconductor Outputs51
Analogue Output51
EMC-Compliant Wiring51
Display Menu - Configuration56
Create Configuration Overview56
Operate Rotary Knob57
Configure Speed Monitor57
Password Protection58
Use Chip Card59
Insert Chip Card60
Write Data to Chip Card60
Read Data from Chip Card61
Transfer Device Parameters62
Duplicate Chip Card62
Compatibility with Older Device Versions63
Special Cases and Problem Solving64
Save Configuration with Software Smartcardcommander65
Menu Overview67
Permanent Display67
Basic Settings Ini Pnp Pnp67
Basic Settings for the Rotary Encoder68
Settings70
Advanced Settings78
Information81
Restart82
Menu Messages83
Example: Configure Basic Configuration 286
Create Configuration in Pnozsigma Configurator87
Download Project from the Pnozsigma Configurator to the PNOZ S3087
Transfer Project from PNOZ S30 to the Pnozsigma Configurator88
Function Test During Commissioning90
Operation and Diagnostics91
LED Indicators91
Display92
Error Stack Entries92
Current Error Messages92
Open Circuit Message100
Frequency Difference Message on Proximity Switch100
Function Test of the Relay Outputs101
Technical Details102
Safety Characteristic Data108
Signal Level of the Encoders109
Supplementary Data110
Service Life Graph of Output Relays110
Permitted Operating Height111
Categories112
Safety Level112
Safety Functions114
Safety-Related Characteristic Data for Operation with Non-Safety-Related Rotary Encoder114
Permitted Encoder Types and Output Signals114
Safety-Related Architecture115
Achievable Safety Level115
Safety-Related Characteristic Data for Operation with Non-Safety-Related Rotary Encoder with115
Permitted Encoder Types and Output Signals115
Safety-Related Architecture116
Achievable Safety Level116
Safety-Related Characteristic Data for Operation with Non-Safety-Related Rotary Encoder with116
Permitted Encoder Types and Output Signals116
Requirements of the Drive Controller117
Safety-Related Architecture117
Achievable Safety Level118
Safety-Related Characteristic Data for Operation with a Safe Rotary Encoder118
Permitted Encoder Types and Output Signals118
Safety-Related Architecture118
Achievable Safety Level119
Safety-Related Characteristic Data for Operation with a Safe Rotary Encoder with Z Index119
Permitted Encoder Types and Output Signals119
Safety-Related Architecture120
Achievable Safety Level120
Safety-Related Characteristic Data for Operation with Non-Safety-Related Rotary Encoder and120
Permitted Encoder Types and Output Signals120
Proximity Switch121
Safety-Related Architecture121
Achievable Safety Level121
Safety-Related Characteristic Data for Operation with 2 Proximity Switches122
Permitted Encoder Types and Output Signals122
Safety-Related Architecture122
Achievable Safety Level123
Safety Characteristic Data for Operation with 2 Proximity Switches with Reduced Diagnostics123
Permitted Encoder Types and Output Signals123
Safety-Related Architecture124
Achievable Safety Level124
Examples125
Connection of Proximity Switch125
Features125
Configuration Overview125
Incremental Encoder Connection127
Features127
Configuration Overview127
Order Reference129
Product129
Accessories129
EC Declaration of Conformity132
UKCA-Declaration of Conformity133

Pilz PNOZ s30 - Example: Configure Basic Configuration 2

Table of Contents

Related product manuals