PRISMJET 54 Gen2 - Appendix

To Next Page

To Previous Page

PrismJET 54 Gen2 OPERATION MANUAL Appendix

309

8 Appendix

This chapter describes specifications and included components with this printer.

Main Page

Safety Instructions3
Types and Meanings of Warnings4
Important Safety Instructions5
Handling the Warning Labels9
Location and Type of Warning Labels9
Cautions on Handling the Operating Instruction Labels11
Locations and Types of Operating Instruction Labels12
Product Overview13
Names of Parts and Functions14
Front Section14
Rear Section16
Operation Panel17
Operation Keys18
Display Section19
Ink Level Indicator21
Estimated Ink Level Graphic22
Setup Menu Display23
Changing Printer Status23
Before Using25
Power Cable Connection26
Turning the Power On/Off30
Turning the Power off31
Installing Ink Cartridges33
Installing 220 Ml Ink Cartridges35
Installing High Capacity Pack Adapters (Option)40
When Using the High Capacity Pack Adapter for the Printer Whose Ink Is Charged for the First Time44
Loading Roll Media45
Setting Roll Media48
Releasing the Partial Function of Pressure Arms52
Setting the User Type Setting54
Test Print56
Nozzle Check59
Mode Print61
Setup Print62
Palette Print63
Adjust Print64
Standard Adjust Print71
Standard Confirmation Pattern72
Standard Rough Adjustment Pattern78
Print Mode80
Standard Micro Adjustment Pattern82
Custom Confirmation Pattern87
Adjust Print92
Custom Rough Adjustment Pattern93
Rough Pattern ALL93
Pattern Name94
Rough Pattern a to F96
Custom Micro Adjustment Pattern100
Fine Pattern ALL100
Fine Pattern a to F104
Print Information105
Connecting the Printer to Your PC107
System Requirements107
Preparing Cables107
Connecting a Network Interface Cable108
Handling the Printer109
Print Flow Chart110
Media Type111
Cautions on Handling Media111
Printing Area112
Head Height Adjustment113
When Raising the Print Head113
When Returning the Print Head to the Original Position115
Media Feed Adjustment117
Menu Setups on the Operation Panel123
Menu Setup Procedure123
Panel Setup Menu Overview125
Operating from the Operation Panel126
Feeding Media126
Stopping Printing Operation129
Cutting Media Manually131
Procedure for Changing and Confirming Settings While Printing132
Settings that Can be Changed or Confirmed While Printing133
Pausing Printing134
Start Printing During Warm up135
Normal Display While Printing136
Panel Setup Menu139
Setup Menu140
Setup Item141
User Type Menu142
Print Mode Menu144
Effect Menu145
Adjust Print Menu146
Media Thickness Menu146
Dist.adj Menu149
Init.adj.change Menu150
Confirm Print Menu151
Micro Adj.change Menu151
Pre-Heater Menu152
Platen Heater Menu153
Dryer Menu154
Vacuum Fan Menu154
User Copy Menu156
Spitting Menu157
Panel Setup Menu158
Setup Item158
Spitting Pass Count Menu159
Operation159
Side Margin Menu160
Media Initial Menu161
Media Width Menu162
Output Mode Menu164
Ink Drying Time Menu164
Page Gap Menu165
Method of Cut Menu165
Cut Pressure Menu166
Origin Menu166
Prev. Stick Menu168
Standbyheating Menu168
Head Travel Menu169
Multi Strike Menu169
Strike Wait Menu170
Slant Check Menu170
Auto Cleaning Menu171
Idle Auto Cleaning171
Pre-Printing Mode Auto Cleaning172
Longstore Menu173
CR Maintenance Menu174
Initialization Menu174
IP Address Menu175
Subnet Mask Menu175
Gateway Menu176
Header Dump Menu177
Start Feed Menu178
Front Interlace Menu179
Test Print Menu181
Cleaning Menu182
Menu Option Menu183
System Information Menu185
Ink Status Menu185
Life Times Menu186
Sleep Mode Menu186
Timer Setting Menu187
Sleep Mode Start Menu188
Display Menu189
Language Menu189
Temperature Menu189
Length Menu190
Remain Ink Menu190
Job Status Menu191
Print Menu193
Roll Length Menu201
Print Stop Menu203
Near End Menu204
Auto Scan Menu204
Maintenance205
Replacing Consumable Components206
Replacing Ink Cartridges206
Replacement Time206
Replacing Roll Media214
Replacing the Cleaning Wiper226
Cleaning the Printer233
Cleaning the Outer Case234
Cleaning the Inside of the Printer235
Head Cleaning237
Cleaning the Cleaning Wiper238
Cleaning Procedures238
Cleaning Around the Print Head251
Disposal of Waste Fluids265
Disposal Method265
Moving or Transporting the Printer267
Preparation before Moving267
Transporting the Printer269
Long Term Storage270
Performing Initial Charging after Head Cleaning274
Troubleshooting281
Malfunctions and Failures282
Problems in Installation and Introduction282
Cannot Perform the Initial Ink Charge282
Cannot Print at All283
Does Not Work at All after Power Activation283
Does Not Work after Loading the Media283
Media-Related Troubleshooting284
The Media Is Crumpled During Initialization285
The Wrong Media Size Is Set During Initialization285
Printing-Related Troubleshooting286
Printing Is Blurred287
White or Black Lines Appear on Printed Media287
Printing Lines Are Not Straight287
Error Messages289
Status Messages289
Message Type Error Display and Remedies291
Error Requiring Restart294
The Media Is Jammed295
Product Specifications300
Printer Specifications300
Network Interface Specification302
Options/Supply List303
How to Get Help303
For Consumables303

PRISMJET 54 Gen2 - Appendix

Table of Contents