Rigol MSO8000-BND

To Next Page

To Previous Page

connected to a waveform display device to measure the frequency, the measurement

result is the same as the current capture rate.

NOTE

If you press > System > AUX Out to select "PassFail", then in the pass/fail test, when a

pass/fail event is detected, the oscilloscope outputs a pulse from the rear-panel [TRIG OUT]

connector.

To Trigger the Oscilloscope

136

Main Page

Default Chapter3
- Table of Contents3
1 Safety Requirement17
- General Safety Summary17
- Safety Notices and Symbols19
- Measurement Category19
- Ventilation Requirement20
- Working Environment20
- Care and Cleaning22
- Environmental Considerations22
2 MSO8000 Series Overview24
3 Document Overview26
4 Quick Start28
- General Inspection28
- Appearance and Dimensions29
- To Prepare for Use29
- Front Panel Overview37
- Figure 4.12 Probe Compensation37
- Figure 4.13 Front Panel Overview37
- Table 4.1 Front Panel Description37
- Rear Panel Overview39
- Figure 4.14 Rear Panel Overview39
- Front Panel Function Overview41
- To Use the Security Lock58
- Figure 4.22 to Use the Security Lock58
- To Use the Built-In Help System59
- Figure 4.23 Help Information59
- To View the Option and the Option Installation60
5 To Set the Vertical System63
- To Enable or Disable the Analog Channel63
- To Adjust the Vertical Scale64
- Vertical Expansion65
- To Adjust the Vertical Offset66
- Channel Coupling67
- BW Limit68
- Probe Ratio68
- Table 5.2 BW Limit68
- Table 5.3 Probe Ratio69
- Input Impedance70
- Waveform Invert70
- To Set the Probe71
- Amplitude Unit72
- Channel Delay73
- To Set the Bias73
- Figure 5.2 Zero Offset73
- Channel Label74
- Figure 5.3 Label Editing Interface74
6 To Set the Horizontal System76
- To Adjust the Horizontal Time Base76
- To Adjust the Horizontal Position77
- Delayed Sweep78
- Figure 6.1 Delayed Sweep Mode79
7 To Set the Sample System81
- Timebase Mode81
- Acquisition Mode84
- Sampling Mode86
- Sample Rate87
- LA Sample Rate88
- Memory Depth88
- Figure 7.4 Memory Depth89
- LA Memory Depth90
- Anti-Aliasing90
- Horizontal Expansion90
8 To Trigger the Oscilloscope92
- Trigger Source92
- Trigger Level/Threshold Level93
- Trigger Mode94
- Figure 8.1 Schematic Diagram of the Acquisition Memory94
- Trigger Coupling96
- Trigger Holdoff96
- Noise Rejection97
- Trigger Type97
- Zone Trigger149
- Trigger Output Connector151
- Figure 8.25 Trigger Output Connector151
9 Operations and Measurements153
- Math Operation153
- Auto Measurement187
  - Quick Measurement after AUTO187
  - Measurement Parameter189
10 Digital Voltmeter (DVM) and Frequency Counter215
- Digital Voltmeter (DVM)215
11 Power Analysis (Option)220
- Power Quality220
- Figure 11.1 Connection Diagram of Power Quality Analysis222
- Ripple223
- Figure 11.2 Connection Diagram of Ripple Analysis224
12 Histogram Analysis225
- To Enable or Disable the Histogram Function225
- To Select the Histogram Type226
- To Select the Histogram Source226
- To Set the Measurement Items226
- To Set the Histogram Height227
- To Set the Histogram Range227
- To Enable or Disable the Statistical Function227
- To Reset228
13 Real-Time Eye Diagram and Jitter Analysis (Option)229
- Real-Time Eye Analysis229
- Jitter Analysis233
14 Digital Channel239
- To Select the Digital Channel239
- To Enable/Disable the Digital Channel240
- To Set the Threshold241
- Auto Arrangement Setting241
- To Set the Waveform Display Size242
- To Set the Label242
- Group Setting242
- Waveform Color of the Digital Channel243
15 Protocol Decoding245
- Parallel Decoding245
- Figure 15.1 Schematic Diagram of Parallel Decoding246
- Figure 15.2 Parallel Decoding Event Table250
- RS232 Decoding (Option)252
- Figure 15.3 Schematic Diagram of RS232 Serial Bus252
- Figure 15.4 Schematic Diagram of Negative Logic252
- I2C Decoding (Option)259
- Figure 15.5 I2C Serial Bus259
- Figure 15.6 I2C Decoding Event Table261
- SPI Decoding (Option)264
- Figure 15.7 SPI Serial Bus264
- Figure 15.8 SPI Decoding Event Table268
- LIN Decoding (Option)269
- Figure 15.9 LIN Decoding Event Table272
- CAN Decoding (Option)276
- Figure 15.10 Sample Position277
- Figure 15.11 CAN Decoding Event Table279
- Flexray Decoding (Option)281
- Figure 15.12 Sample Position283
- Figure 15.13 Flexray Decoding Event Table284
- I2S Decoding (Option)286
- Figure 15.14 I2S Decoding Event Table289
- 1553B Decoding (Option)291
- Figure 15.15 1553B Decoding Event Table292
16 Reference Waveform295
- To Enable the Ref Function295
- To Select the Reference Channel295
- To Select the Ref Source295
- To Adjust the Ref Waveform Display296
- To Set the Label297
- To Export to Internal or External Memory298
- To Import from Internal or External Memory298
17 Pass/Fail Test299
- To Enable or Disable the Pass/Fail Test Function299
- To Start or Stop the Pass/Fail Test Operation299
- To Select the Source299
- To Create a Mask300
- To Save a Mask301
- To Load a Mask301
- To Set the Output Form of the Test Results301
- To Enable or Disable the Display of the Statistics of the Test Results302
- To Reset Statistics303
18 Waveform Recording and Playing304
- Common Settings304
- Record Options305
- Figure 18.1 Recording Process305
- Play Options307
19 Search and Navigation Function308
- Search Function308
- Navigation Function310
20 Display Control312
- To Select the Display Type312
- To Set the Persistence Time312
- To Set the Waveform Intensity313
- To Set the Screen Grid313
- To Set the Grid Brightness314
- Show Scale314
- Color Grade314
- Waveform Freeze314
21 Function/Arbitrary Waveform Generator (Option)316
- To Output Basic Waveforms316
- To Output the Arbitrary Waveform326
- Modulation331
- Sweep334
- Burst336
22 Store and Load338
- Storage System338
- Storage Type338
  - Binary Data Format (.Bin)341
- Load Type344
- Internal Storage and Load344
- External Storage and Load346
- Disk Management347
- Factory Settings354
- Table 22.4 Factory Settings354
23 System Utility Function Setting374
- Remote Interface Configuration374
- System-Related378
24 Remote Control394
- Remote Control Via USB395
- Remote Control Via LAN395
- Remote Control Via GPIB396
- Figure 24.1 Search for the Available Device397
- Figure 24.2 Confirm the Available Device397
25 Troubleshooting398
26 Appendix400
- Appendix A: Options and Accessories400
- Appendix B: Warranty401
  - Index402

Rigol MSO8000-BND - Page 152

Table of Contents

Related product manuals